zx7 sprocket torque specs

You search Auto repair manual PDF zx7 sprocket torque specs, if there are search results will appear below. If search results do not exist, please search by others keyword.



  zx7 sprocket torque specs Direct Download speed 5282 Kb/s

  zx7 sprocket torque specs Full Version speed 6162 Kb/s



HARLEY DAVIDSON CHROME BELT SPROCKET COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
Installation 1. Remove rear wheel. Refer to the applicable Service Manual for the proper removal procedure. 2. Remove bolts and washers from sprocket. •If you intend to install Acorn Nut and Stud Kit (Part No. 91734-85), refer to that Instruction Sheet at this time (please note that this Acorn Nut and Stud Kit does not fit Sportster (XL) models). •If you do not intend to install Acorn Nut and Stud Kit (Part No. 91734-85), retain bolts and washers for reassembly. Proceed to Step 3. 3. Position sprocket cover so that its mounting holes align with the holes in the sprocket. NOTE There is only one position which allows each hole in the cover to align with a hole in the sprocket. If replacement bolts, washers, or nuts are required, use only genuine Harley-Davidson parts specified for your particular model. Aftermarket fasteners can adversely affect performance, which could result in death or serious injury. NOTE • See Harley-Davidson service manual for proper torque val- ues; •Aftermarket fasteners may not have the specific property requirements to perform properly. 4. Install bolts with washers through holes in sprocket cover and sprocket, and into threaded holes in wheel hub. Depending on the tensile strength grade of the bolts in your particular application, tighten bolts in a crosswise pattern to one of the torque values listed in the following table: 5. Refer to the applicable Service Manual for the proper procedure and perform the following: •Install axle. •Align belt. •Adjust belt tension. •Tighten rear axle nut to 60 – 65 ft-lbs torque. 6. Check sprocket for radial runout (eccentricity). If runout is visible, mark outer edge of sprocket at the location of runout. Loosen sprocket bolts and tap the marked location with a rubber mallet. Tighten sprocket bolts in a crosswise pattern to the applicable torque specified in Step 4.

Incoming search terms:

HARLEY DAVIDSON CHROME SPROCKET HARDWARE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 14-02-2011

download
INSTALLATION For 1991 through 1996 XL with Laced Wheels For 1993 through 1996 Softail with Laced Wheels For 1993 through 1997 Dyna with Laced Wheels 1. Remove the rear wheel. Refer to REAR WHEEL REMOVAL in the Service Manual. 2. Remove all stock sprocket mounting screws, washers and locknuts. 3. Place a new chrome washer onto the threads of each new chrome screw from the kit. Install the sprocket onto the wheel. 4. See Figure 1. Obtain new original equipment locknuts and install on the screws. See Figure 2. Tighten all screws in the sequence shown to 45-55 ft-lbs (61-75 Nm). 5. Install the rear wheel. See REAR WHEEL INSTALLATION in the service manual. Verify the correct axle alignment and check belt deflection per service manual instructions INSTALLATION For 1997 and Later XL with Laced Wheels For 1997 through 1999 Softail with Laced Wheels For 1998 through 1999 Dyna with Laced Wheels For ALL Models with Cast Wheels 1. Remove the rear wheel. Refer to REAR WHEEL REMOVAL in the Service Manual. 2. Remove all stock sprocket mounting screws and washers. 3. Place a new chrome washer onto the threads of each new chrome screw from the kit. Apply 2-3 drops of Loctite 262 (red) to the screw threads, and install the sprocket onto the wheel. Tighten all sprocket screws finger-tight. 4. See Figure 3. Tighten the bolts in the sequence shown to 23 ft-lbs (31.2 Nm). NOTE If 23 ft-lbs (31.2 Nm) is reached before screw is fully seated, remove screw and examine screw and wheel for thread damage. Replace screw or wheel if threads are damaged. 5. After all screws have been tightened to 23 ft-lbs (31.2 Nm), mark a straight line, with a grease pencil, on all sprocket screw heads continuing the line over onto the sprocket. 1 4 2 5 3 30 is04009 Figure 3. Tightening Sequence (Later Laced Wheels and All Cast Wheels) 6. Mark a second line at 30° clockwise from the lines on the sprocket at each screw. NOTE For best results, use Snap-on Torque Angle Gauge TA360 or equivalent. 7. Using the marks as a guide, and using the tightening sequence shown in Figure 3+, turn each screw an additional 1/12 turn or 30° clockwise. 8. Install the rear wheel. See REAR WHEEL INSTALLATION in the service manual. Verify the correct axle alignment and check belt deflection per service manual instructions

Incoming search terms:

Harley-Davidson BAKER COMPENSATING SPROCKET INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 19-04-2012

download
1) Remove the primary chain case cover. Refer to your Factory Service Manual for this procedure. 2) Remove the compensating sprocket nut with a 1-1/2″ socket. A ½” impact gun is best for this task. *) Remove the 1-3/16″ clutch nut. This is a left handed nut so loosen it by turning it in the clockwise direction (as viewed from the left side of the motorcycle). 4) With one hand on the compensating sprocket and one on the clutch assembly, remove the primary drive assembly (compensating sprocket, primary chain, tensioner assembly, and clutch as shown in figure a and set it on a clean surface. 5) Flip the adjuster shoe bracket on the chain tensioner assembly. figure b shows the stock orientation of the adjuster show and bracket. Figure C shows the adjuster show bracket flipped 180°. To flip the shoe bracket, remove the two ¼-28×2 bolts that hold the bracket assembly together. This will allow you to separate the chain tensioner assembly components from the primary chain. Flip the bracket around as shown in figure c . PAGE 4 Figure B Figure A BAKER COMPENSATING SPROCKET INSTALLATION INSTRUCTIONS 6) install the new compensating sprocket, chain, and clutch onto the motor sprocket shaft and the transmission input shaft. The flipped chain tensioner assembly (as shown in figure c ) is not ‘captured’ on the primary chain like the stock configuration. Loosely install the chain tensioner assembly onto the anchor plate bolt. Tighten the compensating sprocket nut to 157+ 7 ft-lbs and the clutch hub nut to 75+ 5 ft-lbs using red Loctite on the threads.

Incoming search terms:

HARLEY DAVIDSON DYNA SPROCKET KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
1991-1992 Dyna models: Screw (5) 3739A 1993-1995 FXDL, 1995 FXD and FXDS, all 1997-1999 Dyna models: Screw (5) 3730A 1993-1995 FXDWG and all 1996 Dyna models: Screw (5) 3769 1991-2005 Dyna models: Washer (5) 6516HW 2000-2006 Dyna models: Screw, with lock patch (5) 3737A 2006 Dyna models: Screw, with lock patch (5) 3873 2007 and later Dyna models: Screw, with lock patch (5) 3109 The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Do not re-use sprocket mounting screws. Re-using sprocket mounting screws can result in torque loss and damage to the sprocket and/or belt assembly. (00480b) Kit Contents There are no Service Parts available with this kit. INSTALLATION NOTES The cotter pin or spring clip for the rear axle nut must be replaced during assembly and is available for purchase from a Harley-Davidson dealer. The five sprocket mounting screws must be replaced when replacing the sprocket. Remove existing sprocket according to service manual instructions. Remove all residual threadlocking agent from fastener holes using an appropriate thread chasing device and compressed air.

Incoming search terms:

2008 FLT Police Models Service Manual Supplement

0

Filed Under (Harley Davidson) by admin on 25-11-2010

download
ITEM SERVICED 14-21 ft-lbs (19.0-28.5 Nm) Drain plug torque Engine oil and filter 4 qt. (3.8 L) Oil capacity Hand tighten 1/2-3/4 turn after gasket contact Filter 63798-99A Chrome filter part number 63731-99A Black filter part number FORMULA+ TRANSMISSION AND PRIMARY CHAIN LUBRICATION (Part No. 99851-05) Lubricant type and capacity Primary chain lubricant Wet: 38 oz. (1124 ml) Dry: 45 oz. (1331 ml) 14-21 ft-lbs (19.0-28.5 Nm) Primary chaincase drain plug torque 1/2-1 turn Adjuster screw free play Clutch adjustment 72-120 in-lbs (8.1-13.6 Nm) Adjuster screw locknut torque 1/16-1/8 in. (1.6-3.2 mm) Free play at hand lever 84-108 in-lbs (9.5-12.2 Nm) Clutch inspection cover torque Dipstick at FULL with motorcycle on jiffy stand and filler plug resting on threads. Lubricant level Transmission lubricant FORMULA+ TRANSMISSION AND PRIMARY CHAIN LUBRICATION (Part No. 99851-05) Lubricant type and capacity 32 oz (0.95 liters) 14-21 ft-lbs (19.0-28.5 Nm) Transmission drain plug torque 25-75 in-lbs (2.8-8.5 Nm) Transmission filler plug/dipstick torque Front: 36 psi (248 kPA) Pressure: solo rider Tire pressure and wear Rear: 36-40 psi (248-276 kPA) Replace if less than 1/32 in. (0.8 mm) of tread pattern Wear 55 in-lbs (6.2 Nm) minimum Spoke nipple torque Wheel spokes 99953-99A (12 oz.) D.O.T. 4 hydraulic brake fluid part number Brake fluid level Front: 0.20 in. (5.0 mm) Fluid level (from top of master cylinder reservoir) Rear: 0.26 in. (6.5 mm) Front: 7-10 in-lbs (0.8-1.1 Nm) Master cylinder reservoir cover screw torque Rear: 12-15 in-lbs (1.4-1.7 Nm) 0.016 in. (0.4 mm) Minimum brake pad thickness Brake pads and discs 75-102 in-lbs (8.5.-11.5 Nm) Brake caliper pad pin torque Front: 0.18 in. (4.5 mm) Minimum brake disc thickness Rear: 0.25 in. (6.3 mm) 0.008 in. (0.2 mm) Maximum brake disc lateral runout (warpage) 10 lb. (4.5 kg) Upward force applied at midpoint of bottom belt strand Drive belt deflection 3/8-7/16 in. (9.5-11.1 mm) FLHTP 1/4-5/16 in. (6.4-7.9 mm) FLHP/FLHPE 40-60 in-lbs (4.5-6.8 Nm) Air cleaner cover bracket screw torque Air cleaner 36-60 in-lbs (4.1-6.8 Nm) Air cleaner cover screw torque LOCTITE MEDIUM STRENGTH THREADLOCKER 243 (BLUE) Air cleaner cover screw Threadlocker Part No. 99642-97 (6 ml) LUBIT-8 SUPER OIL, Part No. 94968-85TV (1/4 fl. oz.) Lubricant part number Clutch cable 35-45 in-lbs (4.0-5.1 Nm) Handlebar switch housing screw torque

Incoming search terms:

HARLEY DAVIDSON SOFTAIL SPROCKET KIT INSTALLATION NOTES

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
NORMAL TOOTH WARRANTY This extended warranty applies only to the normal wear that will occur to the tooth profile geometry on the rear belt sprocket. Normal wear is considered wear that occurs when the protective hard coating has worn away exposing the underlying aluminum, changing the profile of the sprocket tooth significantly. Warranty is for five years from date of purchase with unlimited mileage. Warranty claims will require a dated receipt showing proof of purchase from an authorized Harley-Davidson Dealer. Warranty only applies to original purchaser of the sprocket. Original owners name must appear on the receipt. All applications of the sprocket require installation of upper and lower original equipment belt guard, or Harley-Davidson accessory belt guards where applicable. Warranty is voided if these items are not installed. Excessive chips found in the tooth profile due to abnormal riding conditions will void warranty. Occasional chips in the tooth are to be considered normal and should not be considered a warranty issue. Decorative external chrome carries the standard parts and accessories 90 day warranty. Staking the flange on the backside of the sprocket will pierce through the chrome, this is to be considered a normal process and should not be considered an issue. All warranty claims must be pursued through your authorized Harley-Davidson Dealer

Kawasaki KVF650/ 700, KSV 700 Camshaft Installation Instructions

0

Filed Under (Kawasaki) by admin on 29-04-2012

download
Liberally apply assembly lube to every surface of the camshaft. Install the camshaft into the cylinder head (the lobes should be pointed down) and align the decompressor shaft dowels with the weight arms. Install one of the camshaft sprocket holder bolts and tighten to less than finger tight, you should be able to move the camshaft very slightly back and forth, roll the crank over until the other bolt hole is exposed and insert the sprocket bolt and tighten to less than finger tight. Install the cam chain tensioner assembly, do not install the spring, spring dowel, washer, and bolt. Using the spring from the cam chain tensioner very slowly push the tensioner shaft in until the cam chain slack has just been taken out, this is witnessed by the very slight lifting of the opposite end of the cam out of the cylinder head cam journal, do not over tighten the cam chain at this point, if you do, remove the tensioner assembly and retract the plunger again and start over. (If it stays too tight it will stretch the cam chain prematurely and cause cam sprocket damage when the engine is assembled) Roll the camshaft toward the back of the machine (clockwise) loading the sprocket bolts against the back of the sprocket bolt holes, while holding the camshaft in that direction, tighten the sprocket mounting bolt to 14 ft/lb of torque. Rotate the engine in the opposite direction that you rotated it earlier and align the TDC mark, tighten the other sprocket-mounting bolt to 14 ft/lb of torque. Verify the cam timing and crankshaft TDC marks are in alignment

HARLEY DAVIDSON HYBRID CAM PLATE AND HIGH FLOW OIL PUMP KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the service manual and follow the instructions to remove the seat and disconnect the battery cables, negative (-) cable first. Retain all seat mounting hardware. Gasoline can drain from the carburetor fuel line when disconnected from fuel valve fitting. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. Wipe up spilled fuel immediately and dispose of rags in a suitable manner. (00256a) NOTES Installing this kit requires removal and installation of the cam support plate. Refer to the service manual for instructions with the following exception pertaining to cam compartment compo- nents: The crank and primary cam sprocket flange bolts are specially hardened, and the flat washers are of a special diameter and have ground surfaces. Use ONLY the parts provided in the Drive Gear Retention Kit (H-D Part Number 25533-99A, sold separately) when installing this kit. -J04804 1 of 7
The cr ank sprocket flange bolts and pr imary cam sproc ket flange bolts ARE NOT interchangeable. 2. Refer to the service manual to remove and discard the crank sprocket flange bolts and primary cam sprocket flange bolts and washers. 3. For 1999 models only: Refer to the service manual to remove and discard the currently installed cam drive sprocket. 4. Refer to the service manual to remove and disassemble the cams from the support plate and oil pump. Discard the support plate and oil pump. 5. For 1999 – 2000 Dyna, 2000 Softail, 1999 – 2000 Touring, and 2001 EFI Touring models only: Inspect the cams, chain, sprockets and chain tensioners for wear, and replace as needed. Refer to the service manual for inspection and replacement procedures. For 2001 – 2005 Dyna, 2001 – 2006 Softail, 2002 – 2006 Touring, and 2001 carbureted Touring models only: Inspect the cams and secondary cam chain for wear, and replace as needed. Refer to the service manual for inspection and replacement procedures. The primary cam chain, primary sprockets and both tensioners will be replaced by new components from the kit. For ALL models and years: Discard the guide, as it will not be used. INSTALLATION 1. ALL models: See Figure 1. Obtain the new Rear Cam Roller Bearing Kit (H-D Part Number 8983) from inside the Cam Service Kit (H-D Part Number 17045-99C, purchased separately), and install as indicated in Step 2. NOTE See Figure 2. If not enough of the splined shaft is exposed to install the sprocket, omit the spacer (4) and proceed to Step 2e. When the bearing inner race is started onto the machined area, remove the flange bolt (5), flat washer (6) and sprocket, then assemble using the spacer (4). Repeat Step 2e to fully install bearing inner race. To center thrust washer, be sure o-ring is installed in relief groove. Damage to bearing cage and engine can occur if thrust washer is not centered. (00473b) 2. See Figure 1. Install the O-ring (5), thrust washer (4) and bearing inner race (3) onto the rear camshaft as follows: a. See Figure 2. To properly locate the thrust washer (2), install the O-ring (3) in the grinding relief groove on the splined end of the rear camshaft between the machined area and the secondary cam sprocket.

Incoming search terms:

Yamaha R1 2007-2008 Frame Slider Installation

0

Filed Under (Yamaha) by admin on 01-01-2012

download
Installation Steps: 1. Remove left and right body panels. 2. Remove the left side engine stud. Mount the left side offset using 99-HB-SH10125080 Socket Cap 10 X 1.25 X 80 Main Engine Stud. Tip: Only tighten enough so you can still move the offset by hand. Loosely mount the left side body panel. Adjust the offset so the frame slider when mounted will clear the bodywork. There is also a groove cut in the offset, this is so the body can clear the offset. 3. With the offset in the correct position remove body and torque down to OEM torque specs. 4. Using one drop of blue thread locker mount the left side puck to the offset with 99-HB- SH10150045 Socket Cap 10 X 1.5 X 45 (Holds puck to offset). Torque down to 30 to 32 foot lbs. 5. Remove the right side engine stud. Mount the right side offset using 99-HB-SH10125080 Socket Cap 10 X 1.25 X 80 Main Engine Stud. Tip: Only tighten enough so you can still move the offset by hand. Loosely mount the right side body panel. Adjust the offset so the frame slider when mounted will clear the bodywork. There is also a groove cut in the offset, this is so the body can clear the offset. 6. With the offset in the correct position remove body and torque down to OEM torque specs. 7. Using one drop of blue thread locker mount the right side puck to the offset with 99-HB- SH10150045 Socket Cap 10 X 1.5 X 45 (Holds puck to offset). Torque down to 30 to 32 foot lbs. 8. Mount left and right bodywork

Incoming search terms:

YAMAHA YZF-R1P YZF-R1PC ASSEMBLY MANUAL

0

Filed Under (Yamaha) by admin on 26-02-2011

download
PREPARATION To assemble the motorcycle correctly, supplies and working space are required. Supplies oils, greases, shop rags. Workshop The workshop where the motorcycle is assembled should be clean and large. The floor should be level. Self-protection Protect your eyes with suitable safety spectacles or safety goggles when using compressed air, when grinding or when doing any operation which may cause particles to fly off. Product hands and feet by wearing safety gloves or doing. SYMBOLS USED ON CRATE CARTON Contents of the transport package are fragile therefore it shall be handled with care. Indicates correct upright position of the transport package. Transport package shall be kept away from rain. Insertion of the lift arm from this side is prohibited. Lift arm inserting position. -1- UNPACKING 1. Remove the frame cover 1. NOTE: To remove the frame cover, cut the vinyl bands around the cover using a cutter or scissors. 2. Remove the bolts 2 (upper bracket). 3. Remove the bolt 3 (front tire). 4. Remove the packing frames 4 (upward and sideways). NOTE: Remove the bolts while holding frame. NOTE: Before starting the assembly, check for damaged or missing parts. The parts are contained in the cartan and the motorcycle for damage, scratches and other defects. -2- PARTS LOCATION 1 Carton box -3- 1 Carton box Screw, washer and special nuts (windscreen) Bolt (front master cylinder) Bolt (handle crown and handlebar) Nut (rear view mirror) Nut (front reflector) Front reflector Vinyl bag 1 Plugs (handle crown) Owner’s manual Rear view mirrors Windscreen – -5- 1. Handlebar 1 2 3 4 5 6 1 1 1 1 2 1 Reservoir tank (brake) Hexagon socket bolt Crown nut Hexagon socket bolt Cap Hexagon socket bolt * V * V V * d = 6 (0.24), r= 12 (0.47) d = 6 (0.24), r= 25 (0.98) d = 8 (0.31), r= 30 (1.18) 2. Front reflector A: Tighten the crown nut to specified torque. Tightening torque: 115 Nm (11.5 m • kg, 85.0 ft • lb) B: Tighten the bolt to specified torque. Tightening torque: 13 Nm (1.3 m • kg, 9.4 ft • lb) C: Tighten the bolt to specified torque. Tightening torque: 13 Nm (1.3 m • kg, 4.4 ft • lb) A: Tighten the screws to specified torque. Tightening torque: 40 Nm (4.0 m • kg, 29 ft • lb) 1 2 3 4 5 2 2 2 4 4 Reflector bracket Reflector Nut Washer Caliper bolt * V V * * d = 5 (0.20) d = 10 (0.39) d = 10 (0.39), r= 30 (1.18) 3. Clutch cable 1 Clutch cable 1 * A: Check the clutch lever for smooth action. CAUTION: Proper cable routing is essential to assure safe motorcycle operation. Refer to “CABLE ROUTING

Incoming search terms:

Incoming search terms: