vespa parts clasica rally 200

You search Auto repair manual PDF vespa parts clasica rally 200, if there are search results will appear below. If search results do not exist, please search by others keyword.

Vespa Rally 200 General specification

0

Filed Under (Vespa) by admin on 11-11-2010

download
Consumption (according to CUNA Standards) : 3 It 100 Km. (78 mls U.S. gals; 94 mls/imp. gals), gasoline-oil mixture i. e. 2% oil. Max. speed (CUNA Standards): 110 Km/h (68 mph). Carrying capacity: 2 persons and 10 Kg. (22 lbs.) of luggage. Range 280 Km (174 mls) Max fuel capacity: 8.2 It. (2.13 U.S. galls or 1.8 imp. galls) (incl. 1.8 It. s 0.47U.S. galls or 0.39 imp.galls of reserve). Wheel base: 1230 mm (48″.4) Handlebar width: 690 mm (27″.6) Total length 1770 mm (69″.6) Max height 1070 mm (42”.1) Min. ground clearance: 130 mm ( 5″.2) Turning radius: 1400 mm (55″.0) Total dry weight 103 Kg. (226.5 lbs) ENGINE: single horizontal cylinder, two stroke rotary distribution: i. e., carburated mixture is regulated bythecrankshaft rotation, with three transfer ports. Bore: 66.5 mm (2″.62) Stroke: 57 mm (2″. 24) Cylinder displacement: 197,97 cc. (12.076 cu. in.) Compression ratio: 1:8.2. IGNITION: by means of an electronic device that offers many advantages, i. e., allowing to produce a higher tension peak reached in a very short time and with a very limited length of the discharge. It follows: 1) Engine regular running also with spark-plugs very dirty. 2) Starting facility when cold. 3) Light ignition and combustion of the fuel. 4) Higher life of the spark – plugs because of a smaller electrodes wear. 5) Unalterability, during the time, of the ignition advance because the traditional mechanical devices exposed to the wear (as the contact breaker cam, contact breaker, sliding block etc.) are not longer present.

Honda CBR 400RR Service and Repair Manual

0

Filed Under (Honda) by admin on 16-12-2011

download
Once you have found al1 the identification nurnbers, record thern for reference when nbuying parts. Since the rnanufacturers change specifications, parts and vendors (cornpanies that rnanufacture various cornponents on the
rnachine), providing the ID nurnbers is the only av to be reasonablv sure that vou are buvina Model, c ~ d e and
production year CBR400RR-J (1988) CBR400RR-K (1 989) CBR400RR-L (t990 and 91) CBR400RR-N (1992 and 93) CBR400RR-R (1 994-on) , the correct parts. Whenever possible, take the worn pari to the dealer so direct cornparison with the new cornponent can be rnade. Along the trail frorn the rnanufacturer to the parts shelf, there are nurnerous places that the part can end up with the wrong nurnber or be listed incorrectly. The two places to purchase new parts for
your rnotorcycle – the accessory shop and the rnotorcycle dealer – differ in the type of parts they carry. While dealers can obtain virtually every part for your rnotorcycle, the accessory shop is usually lirnited to norrnal high wear iterns such as shock absorbers, tune-up parts, various engine gaskets, cables, chains, brake parts, etc. Rarely will an accessory outlet have rnajor suspension cornponents, cylinders, transrnission gears, or cases. Used parts can be obtained for roughly half the price of new ones, but you can’t always be sure of what you’re getting. Once again, take your worn part to the breaker for direct cornparison. Whetherhu~ng new, used or rebuilt parts, the best course is to dea1 directly with sorneone who specialises in parts for your particular rnake. Frame nwnber NC23-1020001 t0 1036454 NC23 t090001 t0 10981 16 NC29-1000001 to 101 0598 NC29-1050001 on NC29-l t00001 on Unofficial (grey) imports
All CBR400RR rnodels in the LIK are unofficial (grey) irnports frorn Japan. The rnajority are second-hand rnachines and are allocated age-related licence plates for UK use (the licence plate letter reflects the production year in Japan), although new CBRs are allocated current year UK registration letter plates. Cornrnon changes rnade prior to sale in the UK are the disabling of the rev-lirniter device (or more correctly ‘speed-lirniter’ device), which is fitted to cornply with Japanese rnarket regulations. The device is located inthe speedorneter head and is linked to th

YAMAHA XVS1100 (L) SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 07-11-2010

download
GENERAL INFORMATION MOTORCYCLE IDENTIFICATION EB100010 VEHICLE IDENTIFICATION NUMBER The vehicle identification number 1 is stamped into the right side of the steering head. MODEL LABEL The model label 1 is affixed to the frame. This information will be needed to order spare parts. 1-2 IMPORTANT INFORMATION GEN INFO EB101000 IMPORTANT INFORMATION PREPARATION FOR REMOVAL PROCE- DURES 1. Remove all dirt, mud, dust and foreign material before removal and disassembly. 2. Use proper tools and cleaning equipment. Refer to the “SPECIAL TOOLS” section. 3. When disassembling the machine, always keep mated parts together. This includes gears, cylinders, pistons and other parts that have been “mated” through normal wear. Mated parts must always be reused or replaced as an assembly. 4. During machine disassembly, clean all parts and place them in trays in the order of disassembly. This will speed up assembly and allow for the correct installation of all parts. 5. Keep all parts away from any source of fire. EB101010 REPLACEMENT PARTS 1. Use only genuine Yamaha parts for all replacements. Use oil and grease recommended by Yamaha for all lubrication jobs. Other brands may be similar in function and appearance, but inferior in quality. EB101020 GASKETS, OIL SEALS AND O-RINGS 1. Replace all gaskets, seals and O-rings when overhauling the engine. All gasket surfaces, oil seal lips and O-rings must be cleaned. 2. Properly oil all mating parts and bearings during reassembly. Apply grease to the oil seal lips. 1-3 IMPORTANT INFORMATION GEN INFO CAUTION: EB101030 LOCK WASHERS/PLATES AND COTTER PINS 1. Replace all lock washers/plates 1 and cotter pins after removal. Bend lock tabs along the bolt or nut flats after the bolt or nut has been tightened to specification

APRILIA ATLANTIC 125 – 200 REPAIR/ SERVICE MANUAL

0

Filed Under (Aprilia) by admin on 19-11-2010

download
DISASSEMBLING THE COMPONENTS – Never use pliers or similar tools to slacken and/or tighten nuts and bolts. Always use a suitable spanner. – Mark all connections (hoses, wiring, etc.) with their positions before disconnecting them. Identify each connection using a distinctive symbol or convention. – Mark each part clearly to avoid confusion when refitting. – Thoroughly clean and wash any components you have removed using a detergent with low flash point. – Mated parts should always be refitted together. These parts will have seated themselves against one another in service as a result of normal wear and tear and should never be mixed up with other similar parts on refitting. – Certain components are matched-pair parts and should always be replaced as a set. – Keep the motorcycle and its components well away from heat sources. ELECTRICAL CONNECTORS To disconnect the electrical connector, follow the procedures below. Failure to comply with these procedures may lead to irreparable damages to the connector and the wiring as well. If present, press the special safety hooks. ENGINE OIL DANGER Prolonged or repeated contact with engine oil may cause severe skin damage. Wash your hands thoroughly after handling engine oil. Do not release into the environment. Dispose of engine oil through the nearest waste oil reclamation firm or through the supplier. Wear latex gloves during servicing. Change engine after the first 1000 km (621 mi) and then every 6000 km (3728 mi), 2.11.2. (Recommended) oil fork , see 1.8.1. FRONT FORK OIL DANGER Modifying the suspension settings or the viscosity of the front fork oil will affect its response. Standard oil viscosity: SAE 20 W. Choose the oil viscosity to determine the type of response required (SAE 5W for a softer suspension, 20W for a stiffer suspension). The two grades can also be mixed in varying solutions to obtain the desired response. F.A. or Fork have special properties, which enable them to retain virtually the same viscosity regardless of temperature to give constant damping response

YAMAHA XVS 650AK (C) SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 26-04-2011

download
IMPORTANT INFORMATION N 300-008 300-016 EB101000 IMPORTANT INFORMATION PREPARATION FOR REMOVAL PROCEDURES 1.Remove all dirt, mud, dust and foreign material before removal and disassembly. 2.Use proper tools and cleaning equipment. Refer to the “SPEClAL TOOLS” section. 3.When disassembling the machine, always keep mated parts together. This includes gears, cylinders, pistons and other parts that have been “mated” through normal wear. Mated parts must always be reused or replaced as an assembly. 4.During machine disassembly, clean all parts and place them in trays in the order of disassembly. This will speed up assem~ bly and allow for the correct installation of all parts. 5.Keep all parts away f REPLACEMENT PARTS 1.Use only genuine Yamaha parts for all replacements. Use oil and grease recom- mended by Yamaha for all lubrication jobs. Other brands may be similar in function and appearance, but inferior in quality. E8101020 GASKETS, OIL SEALS AND O-RINGS 1.Replace all gaskets, seals and O-rings when overhauling the engine. All gasket surfaces, oil seal lips and O-rings must be cleaned. 2.Properly oil all mating parts and bearings during reassembly. Apply grease to the oil seal lips. Page 18 IMPORTANT INFORMATION I 1 T33? WASHERS/PLATES AND COTTER PINS BEARINGS AND OIL SEALS 1.lnstall bearings and oil seals so that the manufacturer’s marks or numbers are visible. When installing oil seals, apply a light coating of  lightweight lithium base grease to the seal lips. Oil bearings liberally when installing, if appropriate. (D Oil seal Do not use compressed air to spin the bear ings dry. This will damage the bearing sur faces. (D Bearing