suzuki c50 front tire removal

You search Auto repair manual PDF suzuki c50 front tire removal, if there are search results will appear below. If search results do not exist, please search by others keyword.



  suzuki c50 front tire removal Direct Download speed 5282 Kb/s

  suzuki c50 front tire removal Full Version speed 6162 Kb/s



2001 – 2002 GL1800/ GL1800A Rear Tire Inspection

0

Filed Under (Honda) by admin on 27-11-2010

download
1. Inspect the motorcycle for a punch mark as described in Identification on page 2. If a punch mark is present no further action is necessary, return the unit to the customer. 2. Qualify the unit/customer as follows: •Is the tire on the motorcycle the original factory installed tire? •Is the air pressure loss more than three psi per month? Note: Refer to page 145 in the Owner’s Manual. “Even tires that are in good condition may lose one to two psi per month if not checked and adjusted regularly” . If the GL1800 meets the above qualifications, proceed with the repair procedure. 3. Place the motorcycle on a lift and secure it on the centerstand. 4. Remove the rear wheel as described on page 14-9 of the Service Manual. 5. Starting at the valve stem/balance mark area, carefully remove the rear tire from the wheel. Be sure to use plenty of commercially available tire lubricant on the inside and outside of both beads. 6. Carefully inspect the entire circumference of both tire beads. Inspect both the inside and outside of the bead for any distortion or injuries. See examples of injuries below. 2001 – 2002 GL1800/GL1800A Rear Tire Inspection GL1800 #6 OCTOBER 2001 MTB 9430 (0109) CUSTOMER INFORMATION: The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely maintain your Honda. These procedures should not be attempted by “do-ityourselfers,” and you should not assume this bulletin applies to your Honda, or that your Honda has the condition described. To determine whether this information applies, contact an authorized Honda dealer. Service Bulletin American Honda Motor Co., Inc. 2001-2002 GL1800/GL1800A Rear Tire Inspection 0110 GL1800 #6*GL1800 #6*0110*2001-2002 GL1800/GL1800A Rear Tire Inspection*GL1800/GL1800A, Rear Tire Inspection, Bead, Tread*Motorcycle*1800 2 of 4 ©2001 American Honda Motor Co., Inc. – All Rights Reserved GL1800 #6 OCTOBER 2001 Inside BeadInjury Outside BeadInjury Outside BeadInjury 7. Carefully inspect the entire circumference of both tire beads. Inspect both the inside and outside of the bead for any distortion or injuries. See examples of injuries below. 8. If there is no evidence of bead damage, re-install the tire on the rim. Be sure to use plenty of commercially available tire lubricant on the inside and outside of both beads. Be sure to align the balance dot with the valve stem. Inflate the tire to 41 psi. Install the wheel assembly on the motorcycle and proceed to the Identification and then to the Warranty section. 9. If any damage or injury is present replace the tire and valve stem. Be sure to use plenty of commercially available tire lubricant on the inside and outside of both beads. Balance the new tire as necessary

Incoming search terms:

Turbo+2 , Roadstar , Quantum Sport , Quantum"GL" , Entourage Owners Manual

0

Filed Under (Uncategorized) by admin on 03-12-2010

download
tracking Any parting within the tread, sidewall, or inner liner of the tire extending to cord material. CT A pneumatic tire with an inverted flange tire and rim system in which the rim is designed with rim flanges pointed radially inward and the tire is designed to fit on the underside of the rim in a manner that encloses the rim flanges inside the air cavity of the tire. Curb weight The weight of a motor vehicle with standard equipment including the maximum capacity of fuel, oil, and coolant, and, if so equipped, air conditioning and additional weight optional engine. Extra load tire A tire designed to operate at higher loads and at higher inflation pressures than the corresponding standard tire. Groove The space between two adjacent tread ribs. Gross AxleWeight Rating The maximum weight that any axle can support, as published on the Certification /VIN label on the front left side of the trailer. Actual weight determined by weighing each axle on a public scale, with the trailer attached to the towing vehicle. Gross Vehicle Weight Rating The maximum weight of the fully loaded trailer, as published on the Certification /VIN label. Actual weight determined by weighing trailer on a public scale, without being attached to the towing vehicle. Hitch Weight The downward force exerted on the hitch ball by the trailer coupler. Innerliner The layer(s) forming the inside surface of a tubeless tire that contains the inflating medium within the tire. Innerliner separation The parting of the innerliner from cord material in the carcass. Intended outboard sidewall The sidewall that contains a white-wall, bears white lettering or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same molding on the other sidewall of the tire or the outward facing sidewall of an asymmetrical tire that has a particular side that must always face outward when mounted on a vehicle. Light truck (LT) tire A tire designated by its manufacturer as primarily intended for use on lightweight trucks or multipurpose passenger vehicles. Load rating The maximum load that a tire is rated to carry fora given inflation pressure. Maximum load rating The load rating fora tire at the maximum permissible inflation pressure for that tire. Maximum permissible inflation pressure he maximum cold inflation pressure to which a tire maybe inflated.
-9- Maximum loaded vehicle weight The sum of curb weight, accessory weight, vehicle capacity weight, and production options weight. Measuring rim The rim on which a tire is fitted for physical dimension requirements. Pin Weight The downward force applied to the 5thwheelor gooseneck ball, by the trailer kingpin or gooseneck coupler.

Incoming search terms:

TOYOTA Suspension Tire Inflation Pressure Compensation and Adjustment

0

Filed Under (Toyota Manuals) by admin on 06-10-2011

download
2004-2010 4Runner 2007-2010 Avalon, Camry, Camry HV, RAV4, Sienna 2008-2010 Corolla, FJ Cruiser, Highlander, Highlander HV, Matrix, Yar is 2006-2010 Land Cruiser, Prius, Tacoma 2005-2010 Sequoia, Tundra 2007-2008 Solara 2009-2010 Venza The purpose of this bulletin is to provide a procedure to adjust tire pressure correctly when outside temperature is significantly colder or warmer than shop temperature. Seasonal temperature change can dramatically alter tire pressure, which can cause the tire pressure warning lamp to illuminate. Tire temperature is dependent on”cold”tire pressure, driving distance and speed, ambient temperature and road surface temperature. As the temperature of the tire changes, air in the tire expands and contr acts, changing the tire’sairpressure. The cold tire pressure for all Toyota models will vary and will need to be adjusted accordingly. “Cold”tire pressure, as shown on the tire pressure label on our vehicles, is generally considered to be the pressure in a tire that has not been driven in the past 4 hours and has been parked outdoors. The TPWS MUST be initialized with the tire pressure marked on the vehicle placard. Tires are then adjusted according to the information in this bulletin to ensure that the TPWS light does not illuminate unnecessarily.

Incoming search terms:

Suzuki GSX1400FE CHASSIS REMOVAL AND INSTALLATION

0

Filed Under (Suzuki) by admin on 17-12-2010

download
REMOVAL SEAT Remove the seat with the ignition key. FRAM COVERS Remove the seat. (*Above) Remove the frame cover mounting secrews (left and right sides). Remove the frame covers by pulling on the hooked parts. PILLION RIDER HANDLE Remove the pillion rider handle by removing the pillion rider handle mounting bolts. SEAT TAIL COVER Remove the seat. (*Above) Remove the pillion rider handle. (*Above) Remove the seat tail cover mounting screws. : hooked part 6-4 CHASSIS Remove the fasteners.(*6-5) Disconnect the seat lock cable A. Disconnect the brake light/taillight lead wire coupler. Remove the seat tail cover. REMOUNTING Remount the seat, frame covers, pillion rider handle and seat tail cover in the reverse order of removal. www.GSX1400FE.co.uk
CHASSIS 6-5 FASTENER REMOVAL AND REINSTALLATION FASTENER REMOVAL Depress the head of fasteners center piece 1. Pull out the fastener. INSTALLATION Let the center piece stick out toward the head so that the pawls 2 close. Insert the fastener into the installation hole. NOTE: To prevent the pawl 2 from damage, insert the fastener all the way into the installation hole. Push in the head of center piece until it becomes flush with the fastener outside face.

Incoming search terms:

Suzuki B-King GSX1300 BK Suspension Removal and Installation

0

Filed Under (Suzuki) by admin on 01-12-2010

download
Front Fork Removal and Installation B823H12206002 NOTE The right and left front forks are installed symmetrically and therefore the removal procedure for one side is the same as that for the other side. Removal 1) Remove the front wheel assembly. Refer to “Front Wheel Assembly Removal and Installation in Section 2D (Page 2D-4)”. CAUTION ! •Make sure that the motorcycle is supported securely. •Do not operate the front brake lever with the front wheel removed. 2) Disconnect the brake hose clamp (1) from the front fender. 3) Disconnect the brake hose (2) from the brake hose clamp. 4) Remove the front fender by removing the bolts (3) , left and right. 5) Remove the reflex reflector for E-03, 24, 28, 33. 6) After removing of the headlight cover upper screws (4), move the headlight assembly forward. 7) Loose the front fork upper clamp bolt (5). NOTE •Slightly loosen the front fork cap bolt (6) to facilitate later disassembly. •Be sure to adjust the rebound damping force adjuster (7) to the softest position before removing the front fork. 8) Loosen the front fork lower clamp bolts (8) and remove the front fork. NOTE Hold the front fork by the hand to prevent sliding out of the steering stem. Installation 1) Set the front fork to the front fork lower bracket temporarily by tightening the lower clamp bolts (1) . 2) Tighten the front fork cap bolt (2) to the specified torque. Tightening torque Front fork cap bolt (a): 23 N·m (2.3 kgf-m, 16.5 lb-ft) 3) Loosen the lower clamp bolts. 4) Set the front fork with the upper surface “T” of the outer tube positioned 3.0 mm (0.12 in) “a” from the upper surface of the steering stem upper bracket. 5) Tighten the front fork lower clamp bolts (1). Tightening torque Front fork lower clamp bolt (b): 23 N·m (2.3 kgf- m, 16.5 lb-ft) 6) Tighten the front fork upper clamp bolt (3). Tightening torque Front fork upper clamp bolt (c): 23 N·m (2.3 kgf- m, 16.5 lb-ft

2004 – 2006 4Runner TIRE PRESSURE SENSING TRANSMITTER ACTIVATION PROCEDURE DURING PDS

0

Filed Under (Toyota Manuals) by admin on 29-10-2011

download
pressure data is transmitted through a Tire Pressure Warning System antenna to the Tire Pressure Monitoring System receiver. The tire pressure sensing transmitter used for the Tire Pressure Monitoring System (TPMS) on 2004 – 2006 model year 4Runner vehicles needs to be activated during Pre-Delivery Service (PDS). 2004 – 2006 model year 4Runner vehicles. NOTE: After all the tire pressure sensing transmitters are activated, the flashing Low Tire Pressure Warning Light goes OFF. The Diagnostic Trouble Codes (DTCs) listed below may be stored in the system until the tire pressure sensing transmitters are activated. The codes will automatically clear when the tire pressure sensing transmitters are activated

Incoming search terms:

SUZUKI INTRUDER 1500 LC BOTH WHEELS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 27-02-2011

download
In order to keep the proper balance on the bike lift, I would suggest that the front wheel be removed first, this is comparatively easier than the rear wheel which will be explained later. Front wheel removal : Remove the end caps, remove the front axle “Pinch Bolt” front left fork ( item (2) in manual ) remove caliper bolts both (2) both sides (2003 model year) secure calipers, secure wheel from dropping while removing axle from left side. Remove front axle, caution : there are (2) spacers on this axle, left & right, make sure you mark them, as they are both different in shape & in length, & must be re-assembled in same order to provide proper cetrallity of the front wheel with the forks & the brake calipers.both spacers have large flanges which go towards the bearing, the right spacer has (2) flanges, the largest dia. goes towards the bearing. ( very important) Now comes the tough part, I had the original stock pipes, so if you have different pipes, or your bike is a different year, (2003) your choices may be different from mine. Remove OEM right side saddlebag, slack off muffler coupling brackets # 8 & # 8a which connect muffler crossover tank to top muffler, this is where the power of the allen socket wrench set will come in handy, they’re pretty tight with the heat,remove top exhaust pipe bracket bolt (item 19 in manual) the top exhaust pipe should now swing down clear of the rear axle. You may be forced to provide more room for the exit and/or re-installation of the rear wheel by removing the bolt which secures the underside mufflet tank on the lower left side of the frame, (item # 13 in manual) then the (2) bolts, ( items # 14 in manual) which will allow the rear muffler body ( lower exhaust pipe ) to be pulled over to the right to provide access for easier rear wheel entry or removal

Incoming search terms:

HARLEY DAVIDSON VRSC SADDLEBAG SUPPORT KIT (WIDE TIRE) REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-03-2011

download
REMOVAL Remove Pillion and Rear Fender NOTE If possible, lift the rear of the motorcycle up so the rear wheel drops to the bottom of shock travel. This will help provide clearance between the rear tire and fender when installing the mounting brackets. 1. Open the rider seat. 2. See Figure 1. Remove rider seat post (1), nut (2), and washer (3) from passenger pillion. Slide grabstrap (4) forward off pillion. Save mounting hardware for kit installation. 3. Push passenger pillion forward to release slot on bottom of pillion from post on fender tongue. 4. See Figure 2. Lift pillion up to remove lanyard (1) from hole in center of passenger pillion (2). Then lift pillion away from motorcycle. 5. Disconnect turn signal and tail light electrical connections from back of rear electrical caddy. Note position for later installation. 6. See Figure 3. Unsnap rear electrical caddy (1) from rear inner fender. 7. Remove and save two fender support bolts (2), washers (3), and grabstrap (4) from rear fender. 1 2 3 4 is03548 1. Rider seat post 2. Nut 3. Washer 4. Grabstrap Figure 1. Passenger Pillion and Mounting 2 1 3 i03571 1. Seat lanyard 2. Hole in pillion 3. Passenger pillion Figure 2. Seat Lanyard and Passenger Pillion 8. Remove four remaining fender support bolts (2) and washers (3) near center of rear fender. 9. Remove rear fender from vehicle. 3 2 4 2 3 2 3 1 is03544 1. Rear electrical caddy 2. Fender support bolt (6) 3. Washer (6) 4. Grabstrap Figure 3. Grabstrap, Rear Electrical Caddy, and Fender INSTALLATION Install Attach/Release Weldment, Rear Fender, and Grabstrap NOTE Apply Loctite 243 (blue) to last four threads of leave-on bracket screws. 1. See Figure 4. Install leave-on bracket (1) to outside surface of inner fender using two button head screws (2) and nuts (3). Tighten screws to 48 Nm (35 ft-lbs). Repeat for opposite side. 2. See Figure 5. Install release/attach weldment (1) to leave- on brackets (2) using two washers (3) and socket head cap screws (4). Tighten screws to 25 Nm (18 ft-lbs). Repeat for opposite side.

SUZUKI M50 / C50 Fuel Injected Models INSTALLATION INSTRUCTIONS

0

Filed Under (Suzuki) by admin on 19-02-2012

download
1. Remove seat and left side covers. 2. Remove fuel tank. We highly recommend you consult the factory service manual for proper removal of fuel tank. Remove fuel tank rear mounting bracket 3. Route wiring harness under frame by fuel tank rear mounting bracket and up left side of the engine. (Fig. 1) 4. Unplug the TPS connector (black) and connect the two white 3-pin connectors in-line with the factory TPS connector. (Fig. 2) 5. Disconnect the factory connector from rear injector and connect to Fuelpak connector. (Fig. 3) 6. Connect other Fuelpak connector to injector. (Fig. 4) 7. Route black wire to battery negative connection as shown. (Fig. 5) 8. Attach Fuelpak to Fuelpak harness and mount next to battery with Velcro. (Fig. 6) 9. Follow the service manual to reinstall the fuel tank.

Incoming search terms:

YAMAHA V-Star 1100 Carburetor Bowl Screw Repair and Removal After Stripping and Pilot Cap Removal

0

Filed Under (Yamaha) by admin on 19-01-2012

download
When I first started working on bike many years ago, I learned the danger of stripping the heads of Philips screws when removing or installing them on motorcycles. I remember the two worst screws were the casing side-cover aluminum screws and carburetor bowl screws. I think I tried every method of screw removal after they were stripped. Vice grips, better tipped screwdriver, hammer, drill, and other tools were used. One way I learned to remove stripped screws is to re-make the Philips head into a flathead screw. Cutting a slot in the top of the screw and then use a flat-head screwdriver to remove the screw. On some parts this technique can work, other parts and screws it may not. The Philips screws on the bottom of the V-Star carburetor bowls are VERY prone to stripping. In fact, I will not start a carburetor cleaning without new hex head screws to replace the original Philips bowl screws. Replace the bowl screws for yourself if you keep the bike, or for the next rider that will appreciate the hex-head screws when they clean the carburetors. Not many other parts on a V-Star have screws that are prone to stripping. This documentation is to help riders with motorcycle maintenance. Some riders will find themselves with the problem of removing stripped screws. A carburetor cleaning can quickly double in time when you realize the hardest part of the job is removing bowl screws after they strip. And then realizing you do not have the replacement hex-head screws available and must now go to the hardware store.

Incoming search terms:

Incoming search terms: