removing atv hand grips

You search Auto repair manual PDF removing atv hand grips, if there are search results will appear below. If search results do not exist, please search by others keyword.



  removing atv hand grips Direct Download speed 5282 Kb/s

  removing atv hand grips Full Version speed 6162 Kb/s



2009 Kawasaki Voyager Heated Grips Installation Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Remove the Factory Grips Before removing the factory grips, the”chromed plastic”grip end caps need to be removed. The chromed plastic ends are threaded on, but have”left hand”threads, which means to unscrew you need to turn them clockwise. (The opposite way that you would normally unscrew something) To do that I recommend using, either a rubber strap wrench, ora sheet of thin rubber used as you would to loosen the lid of ajar. Once Ihadtheend caps off, I used a sharp utility knife to cut through, and peel off the factory rubber grips. (They are only about 1/8″thicksoit’seasytodo.) With the rubber grips off, I removed the chromed ring that is adjacent to the left switch housing. The left ring will come off, witha gentle pull, but the throttle side ring will need to be cutoff, as it’s pressed on. It’seasytodo; I cut it off using wire side cutters (see picture on page 3 below). 2 Factory left and right Grips After removing the chromed end cap, and the factory rubber grips. The chromed plastic ring next to the switch housing needs to be cut off. Note all the ridges on the sleeve, all these except one ridge need to be filed off. 1. Prepare left handlebar for grip installation The left handlebar is pretty easy to prepare, first I cleaned any glue from the bar, and then gently test fit the left grip, be very careful here as it needs to slide on easily. Asper the instructions, ” Do not force the grip on with anything greater than gentle hand force “. Remember after the test fit you need to take it off again. (You could also crack the heated grip if it’stootight). If you find it too tight, as I did sand the bar using sandpaper until it slides on and off easily. On my bike I used an 80 grit sandpaper, and it took approx 20 minutes to geta good fit

Incoming search terms:

HARLEY DAVIDSON AILERON HAND GRIPS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2011

download
LEFT GRIP REMOVAL AND INSTALLATION 1. See Figure 1. Using a T27 TORX® drive head, remove the two screws with flat washers securing the handlebar clamp (3) to the clutch lever bracket. Remove the clamp, and position the clutch hand lever assembly away from the handlebar. 2. Using a T25 TORX drive head, loosen but do not remove the upper and lower switch housing screws (1). 3. Remove the end cap from the existing left hand grip if so equipped. With “glueless” grip: Remove the grip from the han- dlebar. With glued grip: Remove the grip by carefully cutting it away from the handlebar using a sharp blade or knife. NOTE Make sure that the handlebar surface and the inside of the new grip are smooth, dry and thoroughly cleaned of all dirt or adhesive residue. Do not lubricate left handlebar grip before installation. Lubricating grip can cause it to come off while riding, which could result in loss of control and death or serious injury. (00315a) 4. Position the new left grip (4) so the larger diameter portion of the flange (5) is at the bottom. Push the grip fully onto the handlebar. 5. Fit the grooves (2) on the outboard side of the upper and lower switch housing over the flanges on the end of the grip, then loosely fasten the two screws. 6. Position the clutch hand lever assembly inboard of the switch housing assembly, engaging the tab on the lower switch housing in the groove at the bottom of the clutch lever bracket. 7. Align the holes in the handlebar clamp with those in the clutch lever bracket, and loosely fasten the two screws with flat washers. Adjust the switch housing and clutch hand control position for rider comfort. 8. Using a T27 TORX drive head, tighten first the upper, then the lower handlebar clamp screws to 60-80 in-lbs (6.8- 9.0 Nm). 9. Using a T25 TORX drive head, tighten first the lower, then the upper switch housing screws to 35-45 in-lbs (4.0-5.1 Nm)

Incoming search terms:

HARLEY DAVIDSON SPORTSTER HAND GRIPS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
Remove and Install the Left Grip 1. See Figure 1. Using a T27 TORX®drive head, remove the two screws with flat washers securing the handlebar clamp (3) to the clutch lever bracket. Remove the clamp and position the clutch hand lever assembly away from the handlebar. 2. Using a T25 TORX®drive head, loosen but do not remove the upper and lower switch housing screws (1). 3. Remove the end cap from the existing left handlebar grip if so equipped. Remove the grip by carefully cutting it away from the handlebar using a sharp blade or knife. Do not lubricate left handlebar grip before installation. Lubricating grip can cause it to come off while riding, which could result in loss of control and death or serious injury. (00315a) NOTE Make sure that the handlebar surface and the inside of the grip are smooth, dry and thoroughly cleaned of all dirt or adhesive residue. 4. Position the new left grip (4) so the larger flange (5) is at the bottom. Push the grip fully onto the handlebar. 5. Fit the grooves (2) on the outboard side of the upper and lower switch housing over the flanges on the end of the grip, then loosely fasten the two screws. 6. Position the clutch hand lever assembly inboard of the switch housing assembly, engaging the tab on the lower switch housing in the groove at the bottom of the clutch lever bracket. 7. Align the holes in the handlebar clamp with those in the clutch lever bracket, and loosely fasten the two screws with flat washers. Adjust the switch housing and clutch hand control position for rider comfort. 8. Using a T27 TORX®drive head, tighten first the upper, then the lower handlebar clamp screws to 60-80 in-lbs (6.8-9.0 Nm). 9. Using a T25 TORX®drive head, tighten first the lower, then the upper switch housing screws to 35-45 in-lbs (4.0-5.1 Nm). Remove and Install the Right Grip 1. Refer to the RIGHTHANDLEBARSWITCH section of the service manual for removal of the switch housing assembly. This is necessary to access the throttle cables. 2. Refer to the THROTTLECONTROL section of the service manual to disconnect the throttle cables and remove the existing right grip/throttle sleeve assembly. After removal, make sure that the handlebar end is clean and smooth. 3. Follow instructions in the service manual to install the new right grip/throttle sleeve to the handlebar and connect the throttle cables. 4. Verify that the right grip/throttle sleeve rotates and returns freely and does not bind on the handlebar or switch housing.

Incoming search terms:

Baja BA 250 ATV OWNER'S MANUAL

0

Filed Under (Bajaj) by admin on 26-11-2010

download
FUEL AND OIL FUEL Proper fuel is very important for the engine. Ensure there is no dust, dirt, or water which has mixed in the fuel. Use regular unleaded gasoline with an octane number 90 or higher. ENGINE OIL Your 250cc ATV has a four-stroke engine. Please use oil as described in the chart below. By using prescribe oil, you will realize the best lubrication for engine. Use the chart to select a viscosity rating based on the temperature range in your area. NOTE: In very cold weather (below 5°F (-15°C), use SAE10W-30 for good starting and smooth operation. SAE 10W-30 SAE 20W-40 ENGINE TEMP. °C °F -30 -22 40 104 -10 14 0 32 10 50 20 68 30 86 -20 4 FUEL AND OIL 8 LOCATION OF LABELS Read and follow all of the warnings labels on your ATV. Make sure you understand all the labels. Keep the labels on the ATV. Do not remove them for any reason. If a label comes off or becomes difficult to read, you should get a replacement by contacting BAJA INC. 1 – Red Light – Reverse indicator Light illuminates when ATV is in Reverse. 2 – Green Light – Neutral indicator Light illuminates when ATV is in Neutral. 3 – Ignition key switch – Turn right (CW) “RUN”, Turn left (CCW) “OFF”. ATV will only start when ignition key is turned to the “RUN” position. Make sure ignition key switch is in the “OFF” position when not in use

Incoming search terms:

HARLEY DAVIDSON HAND CONTROL LEVER KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 02-02-2011

download
INSTALLATION The rider’s safety depends upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Dav- idson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308a) Brake Lever Wear safety glasses or goggles when removing or installing retaining rings. Retaining rings can slip from the pliers and could be propelled with enough force to cause serious eye injury. (00312a) NOTE Do not remove handlebar clamp or switch housing assembly to remove brake lever. 1. See Figure 3. Remove the retaining ring (4) from the groove in the pivot pin (A). Do not position fingers between hand control lever and handlebar grip. Improper hand positioning can impair control lever operation and cause loss of vehicle control, which could result in death or serious injury. (00032a) 2. Place a 4 mm (5/32-inch) thick insert between the brake lever and the lever bracket. NOTE A section of corrugated cardboard or the eyelet of an ordinary cable strap can be used for this purpose. See Figure 1. 3. See Figure 3. Loosen the brake master cylinder clamp screws. Rotate the master cylinder assembly slightly forward and then slide toward the center of the handlebar. 4. Remove the pivot pin (A) and original equipment (OE) brake lever. Retain the pivot pin for later assembly. 5. Apply a small amount of GM-40M grease (H-D Part No. 42820-04) to the area where the master cylinder pushrod seats against the brake lever. DO NOT apply grease to the stop-light switch contact surface of the lever. See Figure 2. Align the hole in the brake hand lever with the hole in the master cylinder bracket. From the top of the assembly, slide the pivot pin down through the bracket and hand lever. Check that the pushrod (1) is properly seated in the bowl shaped tab (2) on the lever

Incoming search terms:

Suzuki SV 650s OXFORD "Hot Grips" INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 14-02-2012

download
Installation of heated grips on motorcycles is popular in the UK since it’s not unheard of for even the “fair weather biker” to be caught out by a cold snap. Add to this the fact that many operations on a bike are performed by the hands and fingers, which will not perform well when frozen! 1) Before fitting the grips to the SV, a position must be chosen for the controller. The grips, needless to say, have their mounting places predetermined. I chose to make a small bracket for mounting on the top yoke. This allows the control box to sit level with the top surface for an integrated look whilst remaining accessible for operation. First of all- The mounting bracket in place: Picture shows a strip of rubber on either side of the bracket to stop rubbing / vibrations. Using the flat base and sticky pad supplied, mount the controller on the bracket. 2) With the easy bit done, we need to turn attention to the installation of the power feed cable. It would be too easy to leave the grips switched on with the bike parked up, or for kids to switch them on draining the battery and leaving you stranded. With this in mind, we really want to use a suitably rated power feed that is only “on” when the ignition key is turned on. Fortunately enough, the “pointy” SV has a couple of spare contacts in the fuse box which can be tapped for this purpose

Incoming search terms:

Fitting Hondaline Heated Grips to Honda GL1800

0

Filed Under (Honda) by admin on 08-04-2011

download
Then remove the right side fairing trim piece, starting at the bottom inner and working your way upwards. Unscrew the single Allen head bolt holding the lock panel in place and remove the panel. Now to remove the old grips. Tip; If you have chrome cap ends fitted, protect the chrome on the screw by putting some tape on the end of the screwdriver If you’re a cheapskate, and want to save the old grips, run a thin screwdriver or a hacksaw blade around the inside of the grip to loosen the old glue and it will come away easily. Repeat on the right side grip. The Honda instructions tell you to remove the whole throttle grip & boss but you don’t need to go to all that hassle of unscrewing the switch assembly to get at it. Just remove the rubber grip same as described for the left side After removing the switch panel from the Goldwing, drill a 45mm hole with a holesaw. The spot to drill is marked on the inside of the panel. Then just screw the controller knob assembly into position with the three screws provided (second picture) Spread some glue (the Honda stuff if you can get it, or just plain old rubber cement as I’ve used on my last four Goldwings without problems). Spread it more towards the ends and middle of the bar as it will get pushed inward as you push the grips on anyway

KYMCO MXU 375 ATV WINCH MOUNT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Kymco) by admin on 26-10-2010

download
WINCH MOUNT INSTALLATION INSTRUCTIONS 1. Remove molded plastic bumper guard from the ATV. 2. Mount the winch mount weldment (Item 1) to the ATV as shown below. 3. Mount the roller hawse to the winch mount weldment as shown above. 4
4. Mount the winch to the winch mount weldment and route the winch cable through the rollers. (Installer may need to remove rollers to allow cable end to pass through). 5. Wire the winch according to the manufacturer instructions. 6. Re-install the molded plastic bumper guard. 5 *CAUTION BE AWARE OF WHEN THE CABLE STOP CONTACTS THE ROLLER HAWSE AS CABLE IS WOUND IN. FAILURE TO RELEASE MAY CAUSE DAMAGE TO WINCH PARTS OR TO THE ATV. When using the winch to raise and lower a blade a cable stop must be installed. Carefully raise the blade until the top of the push tube’s are no closer than 1″ anywhere on the ATV. Place the Cable Stop onto the Winch Cable up against the Winch Hawse. Secure the Cable Stop to the Winch Cable using the Cable Clamp Assembly as shown in the pictures below.

Incoming search terms:

Triumph Bonneville America And Speedmaster The Freak Installation Instructions and Parts List

0

Filed Under (Triumph) by admin on 29-10-2010

download
INSTALLATION In order to install The Freak, the factory air-box must be removed. Because of it’s design, the factory air-box is not an item that is easily removed. There are several parts that must be removed in order to get the air-box out of the bike in one piece. We recommend using the following method to remove your air box without having to cut it into smaller pieces in order to get it out of the frame. 1. PARTS REMOVAL In order to gain access to the air-box, it is necessary to remove certain parts of the motorcycle to gain access to the air-box area of the frame. Removing the following parts should be the first steps you take. A. Seats – Remove both seats starting with the passenger pillion, if applicable. B. Side cover and grommets – Remove the plastic side cover on the right side (throttle side) of your motorcycle. This is the faux oil-tank cover that has the name of your bike on it. Underneath the side cover there are three rubber grommets (1 on the frame tab, and two on the air-box) that support the side cover. Remove the two that are on the air-box and leave the one on the frame. You will attach the two that you removed to the right side bracket in Section 4C . C. Faux air filter covers – On the right side of the bike, remove the chrome faux air filter covers, by removing the one allen head screw that holds it onto the air-box. On the left hand side (clutch side) remove the faux air filter cover in the same manner, you removed the one on the right. D. Plastic shrouds – on the left side, remove the black plastic air-box shroud, by removing the two allen head screws holding it in place. Then remove the plastic shroud covering your fuse box (this is the piece that surrounds your ignition terminal next to the battery). E. Battery – Remove the battery by unscrewing the torx-head bolt that holds the chrome bracket in place. Remove the chrome bracket and the black plastic cap. Tilt the battery out of the box with the top towards you. Disconnect both battery terminal connectors, negative (-) terminal first. Remove the battery. F. Battery box – Remove the two bolts that hold the battery box to the frame. Pull the battery box out as far as you can, then remove the the ignition terminal from the battery box, by removing the two allen screws that hold it in place from the back. Next, remove the fuse box from the battery box, by pushing it out from the back. It is not necessary to disconnect any of the wiring going to the fuse box, or the ignition terminal. G. Rear fender – Remove the rear fender, by first disconnecting the taillight wires. Follow the wires from the tail light assembly on the inside of the rear fender (left side) towards the front of the bike until you come to the box connector. Disconnect the tail light wires at this connector, being careful not to break it. Once the wiring is disconnected, remove the 6 bolts that hold it to the struts. Have someone hold the fender for you while you are removing all of the bolts so that it does not drop once the bolts are removed. Slide the fender out the rear of the bike. 2. PREPARE THE MOTORCYCLE FOR AIR-BOX REMOVAL To remove the factory air-box without damaging it, it is necessary to lift the bike. We recommend the use of a multi-position ATV/motorcycle jack with a minimum lift height of 10″. A. Setting up the lift – Place the lift under your bike and secure your bike to the lift according to the lift manufacturer’s instructions. B. Raise slightly – Lift the motorcycle to the point where the rear springs are without tension, but NOT to where the rear tire is off the ground. C. Remove the rear springs – Take off each of the rear springs by removing the the two bolts on each spring. Once all the bolts are removed gently pull the springs out off of the studs. If they do not pull off easily, you can raise or lower the bike slightly with the lift to ease tension on the spring. Remember, you should not have the rear tire off the ground at this point. The bike should only be raised enough to relax the tension in the springs. D. Remove the mufflers – Remove the mufflers by loosening the clamp at the exhaust header, and by removing the rear foot peg hangers. If the mufflers are not removed, they can become damaged by the axles in Section 2H . E. Disconnect the carburetors – With a small flathead screwdriver, pull the retainer springs out of the channel of the carburetor intake tubes (the two large black tubes coming from the air box into the back of each carburetor), and simply push them towards the air box off of the carbs

Incoming search terms:

KAWASAKI VULCAN 700/750 CRUZER EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 28-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Place the bike on the center stand. 2. Remove the three clamps attaching the heat shield to the left hand head pipe and set the heat shield aside. 3. Remove the two heat shield clamps attaching the heat shield to the right hand head pipe and set the heat shield aside. 4. Loosen the pinch clamps where the mufflers slip onto the muffler box (the black box in front of the rear tire). Remove the bolt attaching the mufflers to the footrest. 5. Remove the left and right hand mufflers and set them aside. 6. Remove the right hand foot rest and brake pedal assembly from the frame. 7. Loosen the pinch clamps where the head pipes slip into the muffler box. 8. Remove the two nuts that secure the right head pipe to the cylinder head. Repeat this step on the left head pipe and save the nuts for reuse. 9. Remove the left and right hand head pipes. Remove the header flange from each head pipe and save the two flanges for reuse. Set the head pipes aside. 10. Remove the two bolts (one on each side) that mount the muffler box to the frame. Lower the muffler box down and set it aside. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Remove the two bolts from the charcoal canister mount, the canister is located in front of the rear tire. Using the two 6mm x 16mm bolts (supplied) install the centerstand stop bracket, (stamped 205), by aligning the holes in the bracket with the holes in the canister mount. Be sure the bend closest to the holes in the bracket angles towards the rear of the motorcycle and the tang is pointed to the left hand side. Tighten the two 6mm bolts at this time. 2. Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Place the front head pipe into the heat shield, wrap the hose clamp around the head pipe and give the screw three to four turns. Repeat this step with the rear heat shield. Note : The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. Leave them loose at this time. 3. Install a three hole mounting bracket to each muffler as shown in figure 1. Slide one dog bone shaped nut plate under the bracket that is welded to the backside of each muffler. Attach the mounting bracket using two of the 5/16″ flange head bolts (supplied), leave them loose at this time. Note : The muffler bracket stamped #284 is for the right hand muffler, bracket #285 is for the left hand muffler. 4. Install the rear exhaust assembly, with the heat shield attached, to the rear cylinder using the stock flanges and nuts. Install the stock muffler mounting bolts through the rear footrest brackets, the supplied muffler brackets, and finger tighten the nuts. Leave them loose at this time. 5. Repeat step #4 with the front head pipe

Incoming search terms:

Incoming search terms: