parts diagram ss super e shorty carburetor

You search Auto repair manual PDF parts diagram ss super e shorty carburetor, if there are search results will appear below. If search results do not exist, please search by others keyword.



  parts diagram ss super e shorty carburetor Direct Download speed 5282 Kb/s

  parts diagram ss super e shorty carburetor Full Version speed 6162 Kb/s



Harley-Davidson S&S Super E and G Series Shorty Carburetors Installation and Jetting Instructions

0

Filed Under (Harley Davidson) by admin on 24-10-2010

download
throttle linkage with no cable modification. S&S Super E and G carb kits for 1936 to 1989 Big Twins contain a throttle cable guide (11-2339) designed for butterfly type throttle cables, and kits for 1990 and later Big Twins contain a taller throttle cable guide (11-2338) designed for CV type throttle cables. See Picture 2. The two throttle cable guides are interchangeable on the carburetor body, and can be changed very easily to update older carburetors or to accommodate custom throttle cables which are not stock for a particular year chassis. 1981 to Present Sportster Models Stock Sportster models from 1981 to 1987 have two cable throttle system designed for butterfly type carburetors. Sportsters from 1988 to present have a two cable throttle system designed for use with the stock constant velocity (CV) type carburetor. Since the taller #11-2338 cable guide bracket can not be used on a Sportster chassis due to insufficient frame clearance, throttle cables on Sportsters originally equipped with a CV type carburetor must be changed to butterfly style cables. S&S can supply the correct style throttle cables. See S&S Throttle Cable Application Chart. Picture 2 S&S THROTTLE CABLE APPLICATION CHART Length Total Housing Length Vinyl Housing Part Number Open Side Part Number Close Side Fitment 36″ 32″ #19-0430 #19-0431 For Buell with 7/8″ handlebars 36″ 32″ #19-0432 #19-0433 To ’95 ’81-’85 FX and FL; All ’81-’85 XL (Also pre-’81 w/2-cable throttle housing replaced.) For Buell with 1″ diameter handlebar 36″ 32″ #19-0436 #19-0437 ’96-Up 883-1200 XL 39″ 35″ #19-0434 #19-0435 To ’95 Softail (FXSTC, FXST, FLSTC, FLSTF) ’86-’94 FXR, ’93-’95 Dyna 39″ 35″ #19-0438 #19-0439 ’96-Up Softail (FXSTS, FXSTC, FLSTC, FLSTF) ’96-Up Dyna 42″ 38″ #19-0446 #19-0447 To ’95 custom application 42″ 38″ #19-0440 #19-0441 ’96-Up custom application 48″ 44″ #19-0462 #19-0463 To ’95 All FLT Models 48″ 44″ #19-0464 #19-0465 ’96-Up All FLT Models ” 1996 to Present Buells 1996 and 1997 Buells require special S&S butterfly style throttle cables for Buells, which are compatible with the stock 1996-1997 throttle assembly. 1998 and later carburated Buells require installation of stock 1996 – 97 throttle grip and the special S&S Buell style throttle cables when installing Super E or G carburetors. S&S Throttle Kits S&S throttle kits fit 1″ handlebars and can be used on most chassis. (An adapter sleeve is available for use with earlier, 7 ⁄ 8 ” OEM handlebars originally equipped with internal throttle cable.) Barrel fittings on S&S cables readily “plug in” to S&S Super E, G, and stock H-D 1981-’90 butterfly type carb throttle linkage. Kits include one opening and one closing side cable, left and right grips, and handlebar clamps. Kits with 36″, 39″, 42″, or 48″ length cables are available. Length specified refers to overall cable length. Vinyl covered outer housing is 4″ shorter than overall length

S&S Super E and G Series “Shorty” Carburetors REMOVAL, Installation and Jetting Instructions

0

Filed Under (S&S) by admin on 29-10-2010

download
Remove Old Carburetor WARNINGS ● Gasoline is extremely flammable and explosive under certain conditions. Do not smoke around gasoline. Gasoline fumes are toxic when inhaled. Perform installation in a well ventilated area away from open flames or sparks. Any gasoline leak or spill constitutes a health and fire hazard. ● If motorcycle has been running, wait until engine and exhaust have cooled to avoid getting burned during installation. ● Electrical sparks can ignite explosive gasoline fumes. Failure to disconnect battery while working on motorcycle can also result in inadvertent engagement of starter and personal injury. A. Shut off fuel petcock and disconnect battery. B. Remove air cleaner assembly. Drain fuel from existing carburetor. Remove carburetor, manifold, choke cable and any carburetor mounting hardware NOTE – Removing and tightening hard to reach Allen bolts such as carb-manifold mounting bolts and V2 manifold flange bolts can be greatly simplified by the use of Allen ball-end drivers. These tools are available at most automotive and tool supply houses. See Picture 9. Additionally, Performance Plus of Evansville, Indiana, produces a hex wrench specially modified for accessibility of V 2 manifold bolts. Call 812-963-8854 for further information. As alternative, standard hex wrench can be shortened for convenience. NOTE – Some Buell motorcycles have a breather fitting with 90° elbow on rear head. Due to proximity of frame, elbow must be removed before fitting can be taken off engine. Loosen fitting and rotate to position convenient for cutting elbow. Secure fitting by tightening against cylinder head. Elbow may be inaccessible to hacksaw. In most instances, a die grinder with cutoff wheel will remove elbow with little difficulty. If die grinder is unavailable, grasp elbow firmly with pliers and snap off, then remove fitting. CAUTION – Extreme care must be taken to prevent metal chips from entering engine when elbow is removed. S&S recommends packing breather fitting with gease before removing elbow. Metal chips inside engine will cause extensive damage. Installer bears all responsibility for containment of chips and other debris. Picture 2 Picture 4 Picture 3
5 2. Prepare Air Cleaner Backplate NOTE – Fast idle lever screws, part #11-2384, must not be overtightened. Loctite or other thread locking compound may be used sparingly on threads to prevent screws from vibrating loose. CAUTION – Overtightening fast idle screws may damage backplate. A. All engines except V2s 1. Knuckles & Pans, 1936 to 1965 – Press plugs, part #50-8312, into holes in air cleaner backplate. See Picture 2 . 2. Shovels, 1966 to 1979, and Ironhead (IH) XLs, 1957 to 1979 – Press plug, part #50-8312, into hole in air cleaner backplate. See Picture 3 . 3. Shovels 1980 to 1984 and IH XLs 1980 to 1985 – Screw crankcase breather vent elbow fitting, part #50-8110, into hole in air cleaner backplate and angle downward as shown in Picture 4 . On 1983 and 1984 Shovels press plug, part #50-8312, into other hole on left. 4. Assemble fast idle mechanism as shown in Figure A . B. FL V2s 1984 to 1992 1. Press plug, part #50-8312, into hole on left in air cleaner backplate as shown in Picture 5 . 2. Screw vent hose elbow fitting, part #50-8110, into remaining hole at right. See Picture 5 . 3. Assemble fast idle mechanism as shown in Figure A . C. XL V2s 1986 to 1990 1. Press plug, part #50-8312, into hole on right in air cleaner backplate as shown in Picture 6 . 2. Screw vent hose nipple fitting, part #50-8111, into remaining hole at left. See Picture 6 . Elbow fitting, part #50-8110, supplied in kit may also be used in this location if required. 3. Assemble fast idle mechanism as shown in Figure A . D. FL V2s 1993 and up and XL V2s 1991 and up 1. Press plugs, part #50-8312, into both holes in air cleaner backplate as shown in Picture 7 . 2. Assemble fast idle mechanism as shown in Figure A . E. Buell motorcycles, 1994 and up 1. Assemble fast idle mechanism as shown in Figure A. 3. Throttle Preparation NOTE – Throttle grip assembly must be assembled correctly and work freely to prevent possible sticking during operation. Throttle must snap closed when released. Cable routing must be free of tight bends to minimize friction between cable and housing

KTM 60 SX / 65 SX REPAIR MANUAL ENGINE

0

Filed Under (KTM) by admin on 12-11-2010

download
Carburetor adjustment Basic information about the original carburetor setting The original carburetor setting was adapted for an altitude of approx. 500 meters (1600 ft.) above sea level, and the ambient temperature of approx. 20°C (68°F), mainly for off-road use and central European premium-grade fuel (ROZ 95). Mixing ratio 2-stroke motor oil : super fuel 1:40 . Basic information of changing the carburetor setting Always start out from the original carburetor setting. Essential requirements are a clean air filter system, air-tight exhaust system and an intact carburetor. Experience has shown that adjusting the main jet, the idling jet and the jet needle is sufficient and that changes of other parts of the carburetor will not greatly affect engine performance. RULE OF THUMB: high altitude or high temperatures  choose leaner carburetor adjustment low altitude or low temperatures  choose richer carburetor adjustment * WARNING * -ONLYUSE PREMIUM – GRADE GASOLINE ROZ 95 MIXED WITH HIGH – GRADE TWO – STROKE ENGINE OIL . OTHER TYPES OF GASOLINE CAN CAUSE ENGINE FAILURE , AND USE OF SAME WILL VOID YOUR WARRANTY . -ONLYUSE HIGH – GRADE 2- STROKE ENGINE OIL OF KNOWN BRANDS ( I . E .SHELL ADVANCE RACING X). -NOTENOUGH OIL OR LOW – GRADE OILCAN CAUSE EROSION OF THE PISTON . USING TOO MUCH OIL , THE ENGINE CAN START SMOKING AND FOUL THE SPARKPLUG . -INTHE CASE OFA LEANER ADJUSTMENT OF THE CARBURETOR PROCEED CAUTIOUSLY . ALWAYSREDUCETHEJETSIZEINSTEPSOFONENUMBERTOAVOID OVERHEATING AND PISTON SEIZURE . NOTE: If despite a changed adjustment the engine does not run properly, look for mechanical faults and check the ignition system. Basic information on carburetor wear As a result of engine vibrations, throttle valve, jet needle, and needle jet are subjected to increased wear. This wear may cause carburetor malfunction (e.g., overly rich mixture). Therefore, these parts should be replaced after 1000 hours of using. Idling range – A Operation with closed throttle valve. This range is influenced by the idle adjusting screw 1 . Only make adjustments when the engine is hot. The idling speed can be changed by turning the idle adjusting screw. Turning it clockwise produces a higher idling speed and turning the screw counterclockwise produces a lower idling speed. Opening up – B Engine behavior when the throttle opens. The idle jet and the shape of the throttle valve influences this range. If, despite good idling-speed and part-throttle setting, the engine sputters and smokes when the throttle is fully opened and develops its full power not smoothly but suddenly at high engine speeds, the mixture to the carburetor will be too rich, the fuel level too high or the float needle is leaking. Part-throttle range – C Operation with partly open throttle valve. This range is only influenced by the jet needle (shape and position). The optimum part-throttle setting is controlled by the idling setting in the lower range and by the main jet in the upper range. If the engine runs on a four-stroke cycle or with reduced power when it is accelerated with the throttle partly open, the jet needle must be lowered by one notch. If then the engine pings, especially when accelerating under full power at maximum engine revs, the jet needle should be raised. If these faults should occur at the lower end of the part throttle range at a four-stroke running, make the idling range leaner; if the engine pings, adjust the idling range richer

Tuning the HSR42/ 45 Carburetor

0

Filed Under (Tips and Review) by admin on 31-10-2010

download
your Mikuni HSR is fitted with the tuning parts we found to work with the great majority of engine performance modifications. However, the large number of differing exhaust systems and cams available makes it impossible to accommodate all possible combinations with one carburetor set-up. Your HSR will almost certainly run correctly on your engine without exchanging any parts. But, if it doesn’t, you may alter its tuning to suit your engine’s needs by following this guide. Some exhaust system designs strongly interfere with carburetor tuning. For instance, it is very difficult to get smooth and responsive carburetion through the entire rpm range with straight pipes and completely open exhausts. In addition, very small volume, small diameter mufflers are often ‘seen’ by the engine as straight pipes and present the same tuning difficulties. Very long duration cams often cause relatively poor running below about 3,000 rpm, depending upon the individual cam’s intake valve closing point. Such cams cause reverse airflow out the mouth of the carburetor (often called “reversion” or “standoff”) that can be mistaken for a carburetor tuning problem. Harley-Davidson Screamin’ Eagle performance parts are proven and predictable. If you have any doubts about a particular exhaust system, air cleaner or ignition, you may substitute the Harley Screamin’ Eagle parts as a “reality check.” When re-tuning is required, it usually involves small alterations to the idle and/or main system. The following pages supply enough information to make such alterations relatively simple. Please note that there is no point in attempting to tune any carburetor unless the engine is sound and in a good state of tune. If you have any doubts about the general condition of your engine, have it checked by your dealer or an experienced mechanic before attempting to fine-tune your Mikuni.

HSR Carburetor Total Kits Installation Instructions

0

Filed Under (Mikuni) by admin on 31-10-2010

download
Intake Manifold: 1. Install MAP sensor in Mikuni manifold (Twin Cam only). 2. Attach the Mikuni manifold to the engine. Align the manifold before tightening the bolts. The flange surface of the Mikuni manifold should be parallel with the front of the engine’s cam cover. Use a level or angle meter to check this. Tighten the manifold bolts. 3. Attach the rubber flange to the Mikuni manifold with the furnished 5/16″x3/4″ bolts and washers. Choke Cables: Mikuni & Harley-Davidson Route the cable with largest radius bends possible. Check the cable for free-play after installation. If there is no free-play, the engine may run rich and deliver poor performance or low fuel mileage. Harley Cable (Twin Cam Kits: 42-19, 45-4) : 1. Remove the Harley choke cable from the stock carb. 2. Remove the spring and plunger from the cable. 3. Remove the spring and plunger from the Mikuni. 5. Install the Mikuni spring and plunger onto the Harley choke cable. Change nothing else; be sure to use the Harley plastic nut, not the Mikuni nut (See Figure 1). Total Kit Installation Instructions The HSR series carburetors are precise yet durable instruments; however, like any other piece of fine equipment, they require correct installation and reasonable care to assure optimum performance and long life. Extra time spent during installation will pay off in both short and long term performance and reliability. This Mikuni HSR carburetor kit is designed to be a bolt-on application, and as such, is set-up and jetted properly for most applications. However, since Harley-Davidson motors are often highly modified, alternate tuning settings may be required. The Mikuni Tuning Manual helps make jetting alterations and adjustments an easy matter. NOTE: Carburetor Kits not designated as C.A.R.B. exempt, are not legal for motor vehicles operated on public highways in the state of California, or in any other states and countries where similar laws apply. WARNING NOTE: NOTE: WARNING CAUTION NOTE: NOTE: TK-2 6. Install the new assembly into the Mikuni carburetor. Be careful to only gently tighten the plastic nut. 7. Loosen the knurled plastic friction nut behind the choke knob and check for free-play (see Figure 2). Figure 1: Harley nut with Mikuni spring & plunger Figure 2: Choke cable adjustments Mikuni Cable (Evo Kits: 42-8, 45-2 & 45-3) : 1. Remove nut, spring and plunger from the Mikuni. 2. Install the nut, spring and plunger onto the cable. 3. Install the assembly into the Mikuni HSR carburetor. Be careful to only gently tighten the plastic nut. 4. Check for free-play. Adjust the cable as necessary. An optional choke cable mounting bracket is included in the Evo kits for custom installations. Carburetor Installation: 1. Insert the carb fully into the rubber flange, align with engine and tighten the clamp. 2. Slip the fuel hose onto the carburetor’s fuel fitting and secure with the enclosed hose clamp. NOTE: Some Twin Cam installations may require removal of a small amount of fin material from the cylinders to clear the float bowl. Throttle Cables The HSR carburetor uses stock 1990 and later Harley- Davidson cables. However, if your Harley is fitted with some other carburetor, you may need to purchase a set of cables. See your dealer for the correct cable set. 1. Route the throttle cables with large radius curves and so they do not interfere with other components. 2. Screw the cable adjusters together to make them as short as possible. 3. Connect the “close” cable first (see Figure 3). 4. Install the “open” cable next (see Figure 3). 5. Adjust the opening cable until the slide can be opened fully. Snug the adjuster lock nut. 6. Turn the handlebar to the right and adjust the throttle free-play with the closing cable adjuster to approximately 1/8″ (see Figure 4)

Related Item : yhs-fullyhosted_003 (4)what is round plastic thing on bottom of intake valve on mikuni carb on yamaha four wheeler (2)mikuni am3 w/automatic choke (2)mikuni vm12sc carburetor (2)mikuni 50L01D (2)how to disassemble the float bowl cover off of mikuni carb (2)mikuni bs38 dimensions (2)mikuni bsr 36 einstellen (2)Karburaktor mekuni Bs 26-187 (2)bst36ss (2)