harley davidson 103 engine problems

You search Auto repair manual PDF harley davidson 103 engine problems, if there are search results will appear below. If search results do not exist, please search by others keyword.



  harley davidson 103 engine problems Direct Download speed 5282 Kb/s

  harley davidson 103 engine problems Full Version speed 6162 Kb/s



HARLEY DAVIDSON BLACK ENGINE GUARD KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
REMOVAL NOTE This Instruction Sheet covers several different Harley-Davidson models and years. Be sure to locate and follow the procedures that apply to the motorcycle receiving the new guard. For Models without Lower Fairings 1. Proceed to For All Models section. For Model FLHTCUI (Ultra Classic Electra Glide) with Factory-Installed Lower Fairings 1. Remove the lower fairings following the instructions in the appropriate Service Manual. 2. When the lower fairings have been removed, proceed to For All Models section. For Models FLHR/I (Road King), FLHT (Electra Glide Standard) or FLHTC/I (Electra Glide Classic) with Harley-Davidson Genuine Motor Accessory Lower Fairings 1. See Figure 1. Remove the two black screws (1) that attach the fairing cap (2) to the lower fairing (5). Remove the cap. Set the parts aside for re-installation. 2. Remove the screw (7), rubber washer (8) and locknut (10) and the clamp (9) that attaches the bottom of the lower fairing to the engine guard and set aside. 3. Remove the two locknuts (3), U-bolt (6) and U-bolt retainer (4). 4. Remove the lower fairing by sliding it out from behind the engine guard. 5. Repeat Steps 1 through 4 for the opposite side. 6. Proceed to For All Models section. For Model FLTR/I (Road Glide) with Harley-Davidson Genuine Motor Accessory Lower Fairings Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the battery, negative (-) battery cable first, following the instructions in the appropriate Service Manual. 2. Remove the seat following the instructions in the appropriate Service Manual. 3. Remove the cable strap holding the clutch cable to the engine guard. 4. See Figure 2. Remove the TORX screw (8), rubber washer (9) and locknut (11) and the clamp (10) that attaches the bottom of the lower fairing (4) to the engine guard and set aside INSTALLATION 1. Hold the engine guard in position, and loosely fasten the top of the guard with the new hex socket screw and flat washer from the kit. 2. Install the bottom brackets to the motorcycle frame with the two new TORX screws and locknuts. 3. Tighten all three screws to 15-20 ft-lbs (20.3-27.1 Nm) . For Model FLHTCUI (Ultra Classic Electra Glide) with Factory-Installed Lower Fairings 1. Install the lower fairings following the instructions in the appropriate Service Manual. For Models FLHR/I (Road King), FLHT (Electra Glide Standard) or FLHTC/I (Electra Glide Classic) with Harley- Davidson Genuine Motor Accessory Lower Fairings 1. Carefully place one lower fairing in position from behind the engine guard. 2. See Figure 1. Install the lower fairing to the top of the new engine guard with the U-bolt (6) from the back, through the holes at the top of the fairing. Install the retainer (4) in position on the U-bolt and secure to the engine guard with the two locknuts (3). Do not tighten the locknuts at this time. 3. Attach the bottom of the fairing to the engine guard with the clamp (9) removed earlier. Install the clamp around the engine guard in the direction shown, with the tabs toward the rear of the vehicle and the flat side of the clamp against the lower fairing. Insert the screw (7) through the lower fairing, rubber washer (8) and clamp (9). Secure the assembly with the locknut (10). Tighten to 12 ft-lbs (16.3 Nm) .

Incoming search terms:

HARLEY DAVIDSON V-Series California Engine Owner's Manual

0

Filed Under (Harley Davidson) by admin on 28-11-2010

download
During Break-In At 50 Miles (80 Kilometers): 1- Change engine oil and filter. 2- Inspect for fuel and oil leaks. 3- Inspect air cleaner element and service as required. 4- Check tightness of exterior fasteners, except head bolts. Engine Maintenance at 500 Miles (800 Kilometers): 1- Change engine oil and filter. 2- Inspect for fuel and oil leaks. 3- Inspect air cleaner element and service as required. 4- Check tightness of exterior fasteners, except head bolts. 5- Check operation of enrichment device and throttle controls. 6- Check engine idle speed. 7- Check tightness of engine mounts. Regular Service Intervals Regular lubrication and maintenance will help keep your new S&S engine operating at peak performance. The following table presents the required service schedule for normal operating conditions. Failure to complete the required engine maintenance can result in engine damage and an increase in emissions. Please refer to the motorcycle owner’s manual for any additional required chassis maintenance. Engine Service Intervals Item Interval Engine Oil & Filter Change at 50, 500, 2,500 miles (80, 800, 4,000 kilometers), every 2,500 miles (4,000 kilometers) thereafter1 Air Cleaner Element Inspect at 50 and 500 miles (80 and 800 kilometers), every 2,500 miles (4,000 kilometers) thereafter2 Tappet Oil Screen Inspect every 2,500 miles (4,000 kilometers). Replace every 5,000 miles (8,000 kilometers). Petcock, Lines, & Fittings, Vacuum Lines Inspect at 50 and 500 miles (80 and 800 kilometers), every 2,500 miles (4,000 kilometers) thereafter. Fuel Tank Filter Screen & In-Line Fuel Filter (If used) Inspect every 5,000 miles (8,000 kilometers). Engine Idle Speed Adjust as required. Operation of Throttle & Enrichment Device ControlsInspect at 500 miles (800 kilometers) and every 2,500 miles (4,000 kilometers) thereafter. Spark Plugs Inspect every 5,000 miles (8,000 kilometers). Replace every 10,000 miles (16,000 kilometers) or as needed. Ignition Timing Inspect every 5,000 miles (8,000 kilometers). Engine Mounts Inspect at 500 miles (800 kilometers) and every 5,000 miles (8,000 kilometers) thereafter. External Fasteners Except Engine Head Bolts Re-torque at 500 miles (800 kilometers) and every 5,000 miles (8,000 kilometers) thereafter. 1- S&S recommends that petroleum-based oil not specifically formulated for motorcycles should be changed every 1,000 miles (1,600 kilometers) after the break-in period. 2- Replace more frequently if required or if engine is operated in a dusty environment.

Incoming search terms:

Harley Davidson engine modification

0

Filed Under (Harley Davidson) by admin on 02-11-2010

download
Looking for high performance engine specifications for your Harley- Davidson motorcycle? Need to know what high performance equipment provides the best performance at the lowest costs for your H-D. Here you can look at performance modifications with the dyno runs of many different engine combinations, so you can pick your own equipment, horsepower rating and dollars to spend. An incremental approach to engine development has provided some good results on many engines. Find out what combination of carburetor, camshaft, exhaust systems, ignition systems, head work, pistons and the other high performance components work well. There are tests of some equipment that did not work well. Know what works and what does not. Compare the results of your current bike to those seen here. Are you getting the performance you paid for? If you have had success in your engine development program, send a picture of the bike and your performance results (dyno sheets or time slips) to the V -Twin Café for publication. The V -Twin Café is always looking for good articles on motorcycle performance work. If you write performance oriented articles, contact us. Twin Cam 88 and 95 cubic inches Twin Cam Engines from Harley-Davidson have a good design and some nice upgrades available from the local Dealer including a 95 cubic inch big bore kit. What can you expect from this engine? Here are some engine configurations that have been tested. 45 to 50 HP Stock Evolution Engines are the starting point for all the modifications. The only way to validate what the performance gain was for any change is to have dyno runs before and after. These are the before runs of several bikes. 55 to 65 HP Up to $750 Stage One Evolution Harley-Davidson engines involve no internal changes made to the engine. All modifications are made by changing or modifications to external components on the engine. These components include air cleaners, carburetors, exhaust systems and ignition systems. No special tools or training is required to perform stage one modifications.

Incoming search terms:

HARLEY DAVIDSON SCREAMIN' EAGLE TWIN CAM 110 (1800 CC) CONVERSION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-02-2011

download
REMOVAL Prepare for Service 1. Position motorcycle on a suitable lift. NOTE If vehicle is equipped with Harley-Davidson Smart Security System, see owner’s manual for instructions to disarm the system. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 2. Disconnect battery cables, negative (-) battery cable first. 3. Remove seat according to the instructions in the service manual. 4. Refer to service manual to remove left saddlebag and side cover. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 5. Remove fuel tank according to the instructions in the service manual. Remove Engine Components 1. Remove existing air cleaner assembly. Discard backplate but save remaining parts. Refer to AIR CLEANER REMOVAL in service manual. 2. Remove existing exhaust system. Refer to EXHAUST SYSTEM REMOVAL in service manual. 3. Remove engine from chassis following the instructions in the service manual. 4. Disassemble engine top end and bottom end. Refer to appropriate ENGINE sections in service manual. 5. Remove existing clutch diaphragm spring. Refer to CLUTCH REMOVAL in service manual. The procedures in this instruction sheet should be performed by one experienced in precision measuring techniques. Failure to meet tolerances called for in this instruction sheet can result in engine damage. (00511b) -J04793 1 2 is03517 1. O-ring counterbore 2. Spigot bore Figure 1. Spigot Bore and O-Ring Counterbore Dimensions Table 1. Spigot Bore and O-Ring Counterbore Dimensions Depth Bore Description 1.625 +/- 0.010 in. (41.3 +/- 0.25 mm) 4.205 +/- 0.010 in. (107 +/- 0.25 mm) Spigot Bore 0.085 +/- 0.003 in. (2.16 +/- 0.08 mm) 4.415 +/- 0.002 in. (112 +/- 0.05 mm) O-Ring Counter- bore is03456 Figure 2. Cylinder Wall MACHINE CRANKCASE Crankcase Boring Preparation NOTE During final assembly of the engine, Harley-Davidson recommends replacing the OE cylinder studs with Screamin’ Eagle High Tensile Studs (16505-01). 1. Remove cylinder studs from the engine crankcase. 2. Mask off all bearings and oil holes to prevent debris and contaminants from entering those areas. 3. Inspect and clean engine case mating surfaces. 4. See Figure 6. Reassemble engine case with OE screws, except the top center screw between the cylinders, and tighten to specifications listed in service manual. NOTE To prevent damage to crankcase boring tool, it is important to replace the top center screw with a modified top center screw (1093). This screw is included in the Crankcase Boring Tool Kit (94419-06) and can be purchased separately from a Harley- Davidson dealer. 5. Install modified top center screw (1093) between the cylinders and tighten to 50-90 in-lbs (5.6-10.2 Nm). 6. See Figure 1 and Table 1. Machine crankcase cylinder spigot bore and O-ring counterbore to the dimensions shown. Modify Crankcase

Incoming search terms:

Harley-Davidson Electronic Fuel Injection Tuner INSTALLATION Manual

0

Filed Under (Harley Davidson) by admin on 14-04-2012

download
Harley-Davidson Electronic Sequential Port Fuel Injection System, (ESPFI) This completely new engine management system was released starting with select 2001 model year Softail motorcycles. This system is a speed/density, open loop, sequential port fuel injection design that also controls spark timing and spark intensity. Speed/Density System – When the ECM monitors manifold air pressure, air temperature, throttle position and engine rpm to manage fuel delivery. Open Loop Control – When the ECM monitors sensors positioned on the intake side of the engine and does not monitor the end result of internal combustion at the exhaust. Sequential Port Fuel Injection – When the injector nozzle is positioned in the manifold near the intake valve and is precisely timed to deliver fuel to each cylinder. This ESPFI system is the exclusive design used on 2001 and Later EFI-equipped Softail models, 2002 and Later EFI-equipped Touring models, 2004 and Later Dyna models, and 2004 and later V-Rod models. Current ESPFI Components The following is a list of the major components of Harley-Davidson’s current ESPFI system. It is important to have an understanding of what these components do before learning how the ESPFI system functions. Refer to the appropriate Harley-Davidson Service Manual for the vehicle you are working on for additional information on component design and function and for the physical location and testing procedures for each individual component. ECM – Electronic Control Module – this is the brain of the system that collects input signals from multiple sensors, makes decisions and sends output signals to deliver fuel and spark to the engine. CKP – Crank Position Sensor – this sensor provides input signals to the ECM that indicate engine rpm, (how fast the engine is running in R evolutions P er M inute). The ECM also uses these inputs to determine what stroke the engine is in so it can deliver the fuel and spark at the desired time.

Incoming search terms:

AMSOIL Recommendations for All Harley Davidson

0

Filed Under (Harley Davidson) by admin on 06-02-2011

download
ISSUES: Harley Davidson recommends both gear lube and motorcycle oils for their equipment and there are many different models with corresponding specific oil recommendations. The variety of recommendations can cause confusion and lack of confidence in making the correct AMSOIL lubricant recommendation. The following charts outline the proper sequence of product recommendations for the Harley Davidson products listed. DESCRIPTION & RECOMMENDATIONS: Harley Davidson manufactured 9 types of engines from 1929 to the current model year. Flathead (1929-1974), Knucklehead (1936-1947), Pan- head (1948-1965), Shovelhead (1966-1984), Evolution (Blockhead) 1340 (1984-1999), Twin Cam (2000 to current), V-Rod (Revolution) (2001 to current) Ironhead Sportsters (1957-1984) & Evolution Sport- sters 1985 to current. Harley Davidson recommends SAE 60 or SAE 50 engine oil for Flathead, Knucklehead, Panhead, and Shovelhead equipped bikes . AM- SOIL recommends AHR SAE 60 or MCV 20W-50 motorcycle engine oil for these vintage models. AMSOIL SVT or SVO should be used in transmissions found on these models. Shovelhead is the only model with a chain case that is lubricated via engine oil. AMSOIL recommends MCV 20W-50 motorcycle oil in all 3 holes (engine, transmission, and primary chain case) on Evolution 1340 and all Twin Cam engines. AMSOIL recommends SVT as a secondary oil for the transmission, and SVO as an option for older transmissions. New seals are recommended where excessive leaking is evident. Ironhead, Evolution Sportsters and V-Rod use one lubricant for both the engine and transmission and AMSOIL recommends MCV motorcycle oil for this common sump.

Harley-Davidson Camshaft TC, EVO, Shovelhead, XL EVO, Iron Head, XR Specifications

0

Filed Under (Harley Davidson) by admin on 02-11-2010

download
EVO Black Widow PP8833-2 – 29 55 62 25 264 267 54 103 109 105.8 0.600 0.602 EVO Black Widow PP8826-2 – 27 61 63 29 268 272 56 107 107 107.0 0.602 0.602 EVO Black Widow PP8817-2 – 254 254 0.590 0.590 EVO Carl’s Speed Shop CM4 – 28 44 52 20 252 252 48 98 106 102.0 0.495 0.495 EVO Carl’s Speed Shop CM495F Y 19 47 50 16 246 246 35 104 107 105.5 0.495 0.495 0.179 0.168 EVO Carl’s Speed Shop CM580 – 19 47 50 16 246 246 35 104 107 105.5 0.580 0.580 0.194 0.163 EVO Carl’s Speed Shop CM612 – 36 60 68 28 276 276 64 102 110 106.0 0.612 0.612 0.277 0.235 88 EVO Carl’s Speed Shop CM660 – 38 62 68 28 280 276 66 102 110 106.0 0.660 0.660 0.314 0.277 90 EVO Carl’s Speed Shop CM774 – 284 284 0.784 0.784 0.277 0.236 EVO Carl’s Speed Shop CM780F – 34 70 74 30 284 284 64 108 112 110.0 0.774 0.774 103 EVO Crane EVR0020 – 31 64.5 77 23 275 280 54 107 117 112.0 0.608 0.589 88 EVO Crane Fireball 2000 Y -12 22 20 -10 190 190 -22 107 105 106.0 0.490 0.490 0.026 0.032 EVO Crane Fireball 300 Y 12 34 41 15 226 236 27 101 103 102.0 0.490 0.490 4000 EVO Crane Fireball 310 Y 16 40 43 19 236 242 35 102 102 102.0 0.490 0.490 1500 4500 75 EVO Crane Fireball 316 Y 19 43 48 24 242 252 43 102 102 102.0 0.490 0.490 2000 5000 80 EVO Crane Fireball 326 – 24 48 57 25 252 262 49 102 106 104.0 0.490 0.500 2500 5500 EVO Crane H286 Y 19 43 48 24 242 252 43 102 102 102.0 0.490 0.490 2000 5000 80 EVO Crane H290 – 17 43 45 23 240 248 40 103 101 102.0 0.581 0.581 1800 5200 EVO Crane H296 – 24 48 57 25 252 262 49 102 106 104.0 0.490 0.500 2500 5500 EVO Crane H304 – 24 50 55 25 254 260 49 103 105 104.0 0.600 0.600 2500 5800 EVO Crane H306 – 28 54 69 23 262 272 51 103 113 108.0 0.500 0.510 0.224 0.195 3000 6000 EVO Crane H310 – 23 63 68 28 266 276 51 110 110 110.0 0.550 0.550 0.229 0.229 3000 6500 88 EVO Crane H314 – 26 54 65 21 260 266 47 104 112 108.0 0.600 0.600 2800 6000 EVO Crane HEV0042 – 27 59 71 23 266 274 50 106 114 110.0 0.600 0.576 0.226 0.194 3000 6000 100 116 EVO Crane HEV0067 – 24 50 56 24 254 260 48 103 106 104.5 0.600 0.530 0.128 0.113 EVO Crane HEV0098 – 36 62 72 34 278 286 70 103 109 106.0 0.650 0.650 0.171 0.156 96 EVO CycleRama CR-E550 – 24 52 53 23 256 256 47 104 105 104.5 0.550 0.530 EVO CycleRama CR-E581 – 22 46 53 23 248 256 45 102 105 103.5 0.581 0.550 EVO CycleRama CR-E600A – 24 50 56 24 254 260 48 103 106 104.5 0.600 0.530 EVO CycleRama CR-E600B – 23 51 54 22 254 256 45 104 106 105.0 0.600 0.550 EVO CycleRama CR-E617 – 22 50 50 22 252 252 44 104 104 104.0 0.617 0.617 EVO CycleRama CR-E630 – 18 60 63 13 258 256 31 111 115 113.0 0.630 0.630 EVO CycleRama CR-E660 – 27 59 71 23 266 274 50 106 114 110.0 0.660 0.660 3500 6500 140 EVO Dave Mackie DM500 Y 22 38 52 12 240 244 34 98 110 104.0 0.500 0.500 0.189 0.138 EVO Dave Mackie DM500X Y 25 40 55 20 245 255 45 98 108 102.5 0.500 0.500 0.208 0.178 EVO Dave Mackie DM530 – 28 42 55 15 250 250 43 97 110 103.5 0.530 0.530 0.221 0.141 EVO Dave Mackie DM580 – 26 42 56 12 248 248 38 98 112 105.0 0.580 0.580 0.227 0.144 113 EVO Dave Mackie DM581 – 26 42 56 12 248 248 38 98 112 105.0 0.580 0.580 0.227 0.144 EVO Dave Mackie DM595 – 21 49 57 14 250 251 35 104 112 107.8 0.595 0.595 0.192 0.150 EVO Dave Mackie DM635 – 20 56 59 18 256 257 38 108 111 109.3 0.635 0.635 0.194 0.176 EVO Edlebrock 1740 Y 19 43 48 24 242 252 43 102 102 102.0 0.490 0.490 0.176 0.203 EVO Edlebrock 1741 – 20 46 52 22 246 254 42 103 105 104.0 0.600 0.600 0.183 0.187 EVO Head Quarters HQ-23 – 19 47 52 24 246 256 43 104 104 104.0 0.600 0.530 EVO Head Quarters HQ-24 Y 20 36 52 19 236 251 39 98 107 102.3 0.500 0.500 EVO Head Quarters HQ-25 – 18 38 42 14 236 236 32 100 104 102.0 0.550 0.550 EVO Head Quarters HQ-26 – 20 54 53 22 254 255 42 107 106 106.3 0.600 0.530 89 EVO Head Quarters HQ-27 – 26 60 70 24 266 274 50 107 113 110.0 0.650 0.575

Incoming search terms:

HARLEY DAVIDSON ADVANCED AUDIO CB RADIO KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-03-2011

download
2006 models: communication switch 77173-06 2007 models: communication switch 77173-07 2008 models: communication switch 77173-08 FLHT models will require prior installation of: •Advanced Audio AM/ FM/ CD Radio Kit (76412-06) •AM/ FM Antenna Kit (76325-06 or 76317-06) Unless one has already been fitted as part of another Advanced Audio kit installation: 2006-2007 FLHX models will require the separate purchase of: •fuel tank console (61270-98A), •tank console gasket (71294-89), •a button-head screw (3652), •nut (7964) •clip (10103 and 10120). •tank pod mounting screws (2462) quantity 3 •FLHT trim piece (52447-96) and cb pod trim badge 2008 FLHX models: •fuel tank console (61270-08) •clips (10103 and 10120) NOTE The console screws, fuel door, gasket, mounting bracket will all need to be reused. FLTR models will require the separate purchase of: •a Console Pod Assembly (77136-03), and •three pan-head screws (2462). NOTE See a Harley-Davidson dealer for availability of optional decorative inserts for the Console Pod Assembly. ALL models will require the additional purchase of: •a Non-Ultra Overlay Harness (70169-06), and EITHER : •a Premium Stereo Helmet Headset (77147-98) OR a Hand-Held CB Microphone Kit (76312-98), All of these items are available from a Harley-Davidson Dealer. If two modules are already installed on top of the radio, two Dual-LockTM mounts, (76434-06), will be needed. Models WITHOUT a Tour-Pak installed will require the additional purchase of a Frame Mount CB Antenna Kit (76415- 06). Models WITH a Tour-Pak installed will require the additional purchase of a Tour-Pak Mount CB Antenna Kit (76414-06). All of these items are available from a Harley-Davidson Dealer. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Electrical Overload It is possible to overload your motorcycle’s charging system by adding too many electrical accessories. If your combined electrical accessories operating at any one time consume more electrical current than your vehicle’s charging system can produce, the electrical consumption can discharge the battery and cause vehicle electrical system damage. See a Harley-Davidson dealer for advice about the amount of current consumed by additional electrical accessories, or for necessary wiring changes. (00211b)

Incoming search terms:

2010 Harley-Davidson FLHR Road King front and rear 4-piston braking system Installation

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
in Vivid Black with blue and silver pinstripes, six-speed. Air-cooled, Twin Cam 96™ engine with Electronic Sequential Port Fuel Injection (ESPFI), ABS, security system, cast wheels with independent front and rear 4-piston braking system. Motorcycle generously donated by Harley-Davidson Motor Company Police & Fleet Sales. MSRP excludes all taxes title/documentary fees, registration, tags, dealer prep, labor and installation charges, insurance, optional equipment and accessories, certificate of compliance or non-compliance fees, and finance charges. Delivery must be coordinated through Rockville Harley-Davidson by November 30, 2010. Winner is responsible for any applicable fees above. 6,000 tickets printed. Odds of winning are 1:6,000. Ticket holder need not be present to win. Licensed by the D.C. Lottery and Charitable Games Control Board. Must be 18 years or older to win. No substitutes, return for cash, or other models. As per IRS tax code, amounts paid for chances in a raffle do not qualify as a deductible charitable contribution. Taxes on prizes are the responsibility of the winner. Harley-Davidson is proud to be a sponsor of the National Law Enforcement Officers Memorial Fund. Harley-Davidson Motor Company is a prize provider only, and Harley-Davidson, Inc., and Harley-Davidson Motor Company have no responsibility regarding conduct or administration of the raffle.

Incoming search terms:

Harley-Davidson Twin Cam Engines Cam Chain Drive System Installation and removal MANUAL

0

Filed Under (Harley Davidson) by admin on 27-03-2012

download
Removing the Cam Chain Drive System. NOTES Changing camshafts and cam drives in the 2006-up Harley-Davidson® Twin Cam 88® engines is different than in pervious engines. Procedures require use • of some special tools. Installation should be done by an experienced mechanic with access to factory service manual and required tools. Tighten all fasteners to the correct specifications and in order described. Always use an accurate torque wench. • Incorrect installation can cause engine damage not covered under warranty. CAUTION Failure to install components correctly can result in sudden engine seizure. Engine seizure may result in serous injury to motorcycle operator, passenger, or others. A- Disconnect the battery ground cable to eliminate potential sparks and inadvertently engagement of the starter while working on the motorcycle. B- Remove spark plugs and pushrod cover clips. Collapse the pushrod covers to expose the pushrods. C- Safely elevate and stabilize the rear of the motorcycle. Place the transmission in high gear. Turn the rear wheel to rotate the engine until both lifters and pushrods for either cylinder are at the lowest point on the camshaft (TDC of compression stroke). Both intake and exhaust pushrods for that cylinder will be under pressure from the valve springs and will rotate with light finger pressure. NOTE: 510G camshafts may use stock style non-adjustable pushrods instead of adjustable pushrods. If installing non-adjustable pushrods, disassemble and assemble rocker boxes per H-D® instructions. All other S&S® gear driven cams require installing adjustable pushrods. As a time-saving measure, the stock pushrods can be removed with bolt cutters. Be sure to head caution and warnings of these instructions. D- Cut the pushrods for the cylinder that is at TDC with the bolt cutter and remove the pushrod covers from the engine. Rotate the engine to place the pushrods for the other cylinder at their lowest point. Cut and remove the remaining pushrods. WARNING CAUTION Cutting pushrods with a saw or cutoff wheel may result in debris entering the engine, causing engine damage not covered under warranty. WARNING Cutting pushrods without releasing spring pressure, by rotating the engine until tappets are at the lowest point of travel can result in bodily injury. E- Remove the pushrod covers and lifters form the crankcase. F- Remove engine cam cover and gasket. Secure lifers with a tool made from a large binder clip

Incoming search terms:

Incoming search terms: