Filed Under (Honda) by admin on 29-01-2011
1. Place the faulty radio in the same box in which the exchange radio was sent. THE FAULTY RADIO (CORE) MUST BE RETURNED IN THE SAME BOX IN WHICH THE EXCHANGE RADIO WAS SHIPPED. These boxes are identified by the label shown below which is printed on the inside of the lid. 2. Fill out the pre-printed FedEx airbill that came in the box with the exchange radio. The airbill should have the following address preprinted on it: AHM Remanufactured Parts c/o NK Parts Industries Inc./West 2640 Campbell Rd. Sidney, OH 45365-8836 • Do not use an ordinary FedEx airbill. The pre- addressed airbill has a special account number on it for the exchange program. If you need more airbills, call the Radio Order Desk toll free, not your assigned Parts Center . • Write your dealer number and the warranty claim number in the area shown in the sample airbill ffix the FedEx Airbill to the outside of the box. Radios sent in a box not bearing the correct FedEx airbill will not be accepted for reimbursement under this program. 4. Enclose a copy of the HONDANET for Windows warranty claim in the box. If the claim form is incomplete or not in the box, the faulty radio will be returned to your dealership. 5. Ship the faulty radio to the preprinted address on the airbill. NOTE: Do not ship the faulty radio to the manufacturer or the Warranty Parts Inspection (WPI) Center. 6. For your records, on the repair order include the following: • warranty claim number • original part number • FedEx airbill number When the faulty radio is received, a core credit will be posted to your dealership’s Balance Forward Account. The credit can be identified by the claim number + “CORE” (e.g., 12345/CORE). REMEMBER: A copy of the HONDANET for Windows warranty claim must be included in the box. RETURNING THE FAULTY RADIO The faulty radio must be returned within 20 days of
Filed Under (Harley Davidson) by admin on 09-02-2011
INSTALLATION Remove Existing Equipment To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1. Refer to the Service Manual and follow the instructions given to remove the maxi-fuse. 2. Remove outer fairing and windshield. Refer to OUTER FAIRING/WINDSHIELD REMOVAL in Service Manual. 3 2 1 is 00397 1. Socket head screw (4) 2. Radio support bracket (2) 3. Radio Figure 1. AM/ FM Radio Installation 3. See Figure 1. Using a long shank ball end socket (Snap- on® FABL6E or equivalent), remove the four socket head screws (1) to release the storage box from the left and right radio support brackets (2). Use the oblong holes in the fairing brackets to access the screws. Install Radio 1. Pull the storage box forward to remove the box from the opening in the inner fairing. Discard the storage box. 2. Position the radio (3) between the radio support brackets and push it into the opening in the inner fairing. 3. Align the threaded inserts in the sides of the radio with the oblong holes in the left and right radio support brackets. 4. Starting at the rear, install the four socket head screws previously removed. Alternately tighten the screws to 35- 45 in-lbs (4.0-5.1 Nm). 5. Plug the 23-place radio socket housing [27A] (part of the interconnect harness already installed on the vehicle) into the back of the radio. 6. Remove three T25 TORX® screws that hold the speaker opening cover on one end of the fairing. Discard the cover and screws. Install Speakers 1. See Figure 3. If the speaker (3) and adapter (4) are not assembled, or are assembled incorrectly, orient the speaker on the adapter and grille assembly so the speaker spade contacts are toward the side of the adapter with the widest edge. Snap the speaker into the adapter using finger pressure only.
Filed Under (Honda) by admin on 22-04-2011
INSTALLATION ■ Outline Procedures This section gives general information needed for mounting the individual radio components on and in the fairing. A) Fairing 1) Install radio on fairing before mounting fairing on motorcycle. (Remove fairing from your motorcycle when already mounted). 2) Remove fairing parts. 3) Drill unit mount holes. 4) Install six wire clips. 5) Install windshield on fairing before install- ing speakers. 6) Install radio indicator I on indicator panel II , then install indicator panel on fairing. 7) Install speakers III. 8) Install nutplate IV. 9) Install Power Amplifier in fairing. 10) Install radio funer VI. 11) Install the radio controller VII. 12) Install controller base panel VIII 13) Install radio switch sub-wire. 14) Connect adapter harness and wires inside fairing by working through left turn signal lens hole. B) Motorcycle frame and handlebar 1) Remove travel trunk and seat. Unscrew four shelter bolts (M6, one on each side at front and rear) to route antenna feeder. 2) Install antenna mount and antenna IX. 3) Route antenna feeder along the frame tube. 4) Install radio switch X on left handlebar lever bracket and route the wires. 3 of 11 Page 4 C) Fairing instllation 1) Install fairing on motorcycle. 2) Connect motorcycle wire harness 9-P coupler to fairing wire 9-P coupler. 3) Connect radio switch wire to switch sub- wire.4) Connect antenna feeder. 5) Confirm that radio operates properly. Reinstall parts removed in step 2 or (A) and in step 1 of (B). REWORKING ■ Remove Fairing and Fairing Parts (Fig.10) 1) Install radio on fairing before mounting fairing on motorcycle. (Remove fairing from your motorcycle when already mounted). 2) Remove right and left fairing pockets, right and left turn signal lenses, right and left nutplates, left hole cover and indi- cator base panel from fairing. (Fig.10) Fig. 10 LEI-1 NU I PLATE 4 of 11■ Reworking on Fairing — Speaker mounting holes- 1) Remove 18 mm grommet. 2) Lightly roll template so that it will follow contour of fairing snugly. 3) Position template on fairing with its upper and outer edges aligned with those offairing as indicated by arrows. 4) Attach template to fairing using adhesive tape where shown. 5) Punch mark centers of four holes with a
drift and hammer. 6) Drill 6 mm holes through marked centers. To obtain a more balanced response with richer, deeper bases, drill two 50 mm holes in the fairing so as to link the speaker box with the inside of the fairing. Fig. 11-1
—Power amplifier mounting holes- 7) Drill two 5.5 mm holes through concaves in fairing. Fig. 11-2 RIGHT HAND SHOWN, LEFT SIMILAR ADHESIVE TAPE
Filed Under (Honda) by admin on 29-01-2011
For authorization, call the CB Exchange Radio Order Desk toll free: (888) 997-7278 . The CB Exchange Radio Order Desk hours are Monday thru Friday, 8:30am – 8:00pm EST. BEFORE STARTING ANY REPAIR ON THE CB RADIO, YOU MUST FIRST CALL THE ORDER DESK FOR AUTHORIZATION. Part Number: 08E95-MCA-101RM Honda Code: 7066319 3. After calling the CB Radio Order Desk, an exchange transceiver will be shipped overnight (freight prepaid). 4. Replace the faulty CB Transceiver with the exchange unit (see REPAIR PROCEDURE ). . Remove the seat (see the GL1800 Service Manual, page 2-4). 2. Remove the right rear side cover (page 2-4). 3. Remove the right-hand fairing molding (page 2-8). 4. Remove the right hand top shelter setting bolts and mounting nut (page 2-9). It is not necessary to remove the left-hand fairing molding, shelter bolts, or shelter. 5. Disconnect the 14P CD coupler under the rear seat. Remove and set aside the CD Changer (if equipped). (Continued on page 2) Some customers may experience weak radio transmissions and/or the need to use abnormally high squelch settings for reception on the Hondaline CB Radio. To correct this condition, the CB Transceiver unit must be replaced as described in this Service Bulletin. Do not order a CB kit from parts stock. Follow the ordering procedures in this Service Bulletin. AFFECTED MOTORCYCLES 2001 – 2002 GL1800/A ORDERING AND REPLACING THE CB TRANSCEIVER 1. Before calling the CB Exchange Radio Order Desk, have the following information ready: • VIN • Failure Information (i.e., symptom) • Warranty Status 2. For authorization, call the CB Exchange Radio Order Desk toll free: (888) 997-7278 . The CB
Filed Under (Harley Davidson) by admin on 11-03-2011
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the service manual and follow the instructions given to remove the main fuse. 2. Remove the outer fairing. See the service manual. 3. Remove the fairing cap. See the service manual. 4. FLHX Models: Handlebar-mounted mirrors (purchased separately) are required for proper installation of this handlebar. Removal of the inner fairing may be required, refer to the service manual. If fairing-mounted mirrors are being removed: Install the two small black plugs and large black plugs (purchased separately) to plug the fairing mirror holes. Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) D.O.T. 4 brake fluid will dama ge painted and bod y panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) NOTE Immediately wipe up any brake fluid spillage with a clean, dry, soft cloth. Follow up by thoroughly wiping affected area with a clean, damp, soft cloth (small spills) or washing with a large quantity of soapy water (large spills). Cover nearby motorcycle surfaces with a polyethylene protective sheet to help protect against damage to finish caused by spillage or splashes of DOT 4 brake fluid. 5. Drain the brake fluid from the front brake reservoir and lines per the instructions in the service manual. NOTE Cover the front fender and the fuel tank with clean shop towels to prevent scratching. 6. Models with Radio: Remove the radio. See the service manual. Models without Radio: Remove the storage box. See the service manual. a. The four socket head screws fastening the radio or storage box to the left and right radio support brackets can be accessed through the oblong holes in the fairing brackets. Use a long shank ball-end socket to remove the screws. b. Pull the radio or storage box forward to remove it from the opening in the inner fairing. Remove brake line components carefully. Damage to seating surfaces can cause leakage. (00320a) 7. Remove and retain the button head screw on the underside of the fork stem and bracket assembly that holds the brake line manifold tee. 8. Note the front brake line routing and the orientation of the banjo fittings. Disconnect the brake line from the front brake calipers and the front brake master cylinder assembly. Save the banjo bolts, but discard the two gaskets found at each banjo fitting. See the service manual. 9. Remove the front brake line assembly. NOTES Refer to the parts catalog for this year and model for a replacement OE brake line assembly and clutch cable, if needed. Ask a Harley-Davidson dealer about the selection of Genuine Motor Accessory Custom Braided Clutch Cables and Brake Lines that are available. 10. Remove the front brake master cylinder and clutch lever assemblies from the handlebar. 11. Disconnect the clutch cable from the clutch lever. See the service manual.