gl1800 remove fairing pocket

You search Auto repair manual PDF gl1800 remove fairing pocket, if there are search results will appear below. If search results do not exist, please search by others keyword.



  gl1800 remove fairing pocket Direct Download speed 5282 Kb/s

  gl1800 remove fairing pocket Full Version speed 6162 Kb/s



GL1800 Goldwing Trike Conversion Kit Installation Instructions

0

Filed Under (Honda) by admin on 10-11-2010

download
Disassembly of motorcycle: 1. Place the motorcycle on the center stand or lift. 2. Set the shock preload to zero. 3. Remove the four m8 x 1.25 SHCS from the passenger handles and remove seat. 4. Remove the rear side covers. 5. Disconnect negative battery terminal. 6. Remove the four m8 x 1.25 SHCS and the passenger floorboards. 7. Remove the six m5 x 0.80 BHCS and the foot rest under cover. 8. Remove the six m5 x .80 BHCS and the swing arm pivot bolt covers. 9. Remove the four m8 x 1.25 flange bolts on the rear crash guards. Remove and discard the rear crash guards and bolts. 10. Remove the four #2 Phillips head screws from the inside of the trunk to remove the trim pieces on the sides. 11. Remove the two #2 Phillips head screws in the rear trim molding and remove molding. 12. Remove the seven #2 Phillips head screws from the lower trunk cover. Remove the lower trunk cover. 13. Remove the five #2 Phillips head screws from the trunk opener cover. Remove the trunk opener cover. 14. Disconnect the left and right saddlebag release cables. 15. Remove the five m6 x 1.0 BHCS in the rear fender panel. Remove and discard the rear fender panel and cap screws. 16. Disconnect the trunk wiring. 17. Remove the four m6 x 1.0 flange screws. Remove the trunk from the saddlebag / trunk stay. 7 18. 2005 and older 2005 and older 2005 and older 2005 and older ABS equipped motorcycles: ABS equipped motorcycles: ABS equipped motorcycles: ABS equipped motorcycles: Remove rubber bungee from ABS Control Unit, and save for reinstallation. 19. Remove the two side cover grommets from each saddlebag. ( 4 grommets total ) 20. Remove the left and right hand saddlebag latches, strikers, and release cables for core parts return. Refer to Honda service manual. 21. Remove the left and right saddlebag taillights and sub- harnesses for core parts return . Refer to Honda service manual. 22. Remove the four m6 x 1.0 flange bolts from each saddlebag. Remove and discard the saddlebags. 23. Remove the six m6 x 1.0 flange bolts from the exhaust tips. Slide the tip off the muffler body. Save tips and bolts for reinstallation. 24. Loosen the four m8 x 1.25 SHCS on the muffler clamps. Remove the two m8 x 1.25 flange bolts. Remove and discard the mufflers and muffler gaskets. 25. Remove the four m6 x 1.0 BHCS, two rubber washers, and front fender A. 26. Remove the four m5 x .80 BHCS and chrome front fender covers. 27. 2006 & UP. 2006 & UP. 2006 & UP. 2006 & UP. Remove the Remove the Remove the Remove the two m6 x two m6 x two m6 x two m6 x 1.0 flange bolts on 1.0 flange bolts on 1.0 flange bolts on 1.0 flange bolts on rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. 28. Unplug connector and remove amp and save for Unplug connector and remove amp and save for Unplug connector and remove amp and save for Unplug connector and remove amp and save for reinstallation. reinstallation. reinstallation. reinstallation. 29. Cut lower saddlebag supports off the saddlebag/trunk stay, where the round tubing meets the square, and cut the gusset flush, removing any burrs. See Figure 1. 30. Remove trunk stay for later use. 31. Remove the two m5 x .80 nuts on the license plate light. Remove and discard the license plate ligh

Incoming search terms:

1999-2008 FLHT Series Harley- Davidson Trike Conversion Kit Installation Instructions

0

Filed Under (Harley Davidson) by admin on 04-12-2010

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the ¼ – 20 Phillips head screw and Seat. 6. Disconnect negative Battery Terminal. 7. Remove two ¼ – 20 flanged hex nuts from the Stud Plate. Save the Passenger Handrail and two nuts. 8. Remove the Saddle Bags. 9. Remove the Right and Left Side Covers. 10. Remove Inner Tour Pak Molded Liner. 11. Disconnect the Tour Pak wiring. 12. Remove five ¼ – 20 HHCS, ¼ – 20 nyloc nuts, and Aluminum Spacers. 13. Remove Tour Pak from Top Support Tube. 14. Loosen Muffler Clamp on both Mufflers and remove 2 5/16 – 18 HHCS per Muffler. Remove and discard both Mufflers. Save Muffler Clamps. 15. Remove and discard Muffler Support Plates. 16. Remove both ¼ – 20 HHCS and Front Saddle Bag Brackets. 17. Remove the twelve 5/16 – 18 Torx HCS six 5/16 – 18 nuts, and the Left and Right Saddle Bag Guards. 18. Remove the Air Line Junction from the Rear Fender. 19. Disconnect the Rear Lamp Wiring Harness and remove from T-stud Clip.
6 20. Remove two 5/16 – 18 Phillips head screws. Remove the Left and Right Frame Covers. 21. Remove two 5/16 – 18 Torx HCS. Remove and save the Top Tour Pak Support Tube Top. 22. Remove four 5/16 – 18 Torx HCS. Remove the Left and Right Rear Saddle Bag Guard Support Bracket. 23. Remove four 5/16 – 18 HHCS. Remove and save the Tour Pak Support Tube Bottom. 24. Remove and discard the Air Valve Assembly Bracket. 25. Remove four ½ – 13 HHCS and washers. Remove and discard both Rear Air Shock Absorbers. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. 26. Drain all Brake Fluid from the Rear Brake System. 27. Cut and remove Cable ties and un-clamp Wire Harness Loops from the Rear Brake Line along its length, including Clamps on Swing Arm. 28. Remove the 10 – 24 flanged HHCS and Rear Brake Hose Clamp from the Right Rear Fork Bracket. 29. Remove ¼ – 20 SHCS from Rear Stop Lamp Switch Bracket. 30. Remove and discard Banjo Bolt and Crush Washers on Rear Brake Caliper. 31. Remove the Spring Clip and nut from the Rear Axle. 32. Remove Rear Axle and Rear Wheel Spacers. 33. Push Rear Wheel Assembly forward and slip Rear Belt off of the Rear Sprocket. 34. Remove Rear Brake Caliper. 35. Slide Rear Wheel Assembly rearward. Remove one 5/16 – 18 Torx HCS from inside the Rear Fender well. 36. Slide Rear Wheel Assembly forward. Remove two 5/16 – 18 Torx HCS. Remove Rear Fender. 37. Remove and save the two Retaining Washers from the Stud Plate. Remove and save the Stud Plate

Incoming search terms:

HONDA GL1100 AM/FM RADIO INSTALLATION MANUAL/ WIRING DIAGRAM

0

Filed Under (Honda) by admin on 22-04-2011

download
INSTALLATION ■ Outline Procedures This section gives general information needed for mounting the individual radio components on and in the fairing. A) Fairing 1) Install radio on fairing before mounting fairing on motorcycle. (Remove fairing from your motorcycle when already mounted). 2) Remove fairing parts. 3) Drill unit mount holes. 4) Install six wire clips. 5) Install windshield on fairing before install- ing speakers. 6) Install radio indicator I on indicator panel II , then install indicator panel on fairing. 7) Install speakers III. 8) Install nutplate IV. 9) Install Power Amplifier in fairing. 10) Install radio funer VI. 11) Install the radio controller VII. 12) Install controller base panel VIII 13) Install radio switch sub-wire. 14) Connect adapter harness and wires inside fairing by working through left turn signal lens hole. B) Motorcycle frame and handlebar 1) Remove travel trunk and seat. Unscrew four shelter bolts (M6, one on each side at front and rear) to route antenna feeder. 2) Install antenna mount and antenna IX. 3) Route antenna feeder along the frame tube. 4) Install radio switch X on left handlebar lever bracket and route the wires. 3 of 11 Page 4 C) Fairing instllation 1) Install fairing on motorcycle. 2) Connect motorcycle wire harness 9-P coupler to fairing wire 9-P coupler. 3) Connect radio switch wire to switch sub- wire.4) Connect antenna feeder. 5) Confirm that radio operates properly. Reinstall parts removed in step 2 or (A) and in step 1 of (B). REWORKING ■ Remove Fairing and Fairing Parts (Fig.10) 1) Install radio on fairing before mounting fairing on motorcycle. (Remove fairing from your motorcycle when already mounted). 2) Remove right and left fairing pockets, right and left turn signal lenses, right and left nutplates, left hole cover and indi- cator base panel from fairing. (Fig.10) Fig. 10 LEI-1 NU I PLATE 4 of 11■ Reworking on Fairing — Speaker mounting holes- 1) Remove 18 mm grommet. 2) Lightly roll template so that it will follow contour of fairing snugly. 3) Position template on fairing with its upper and outer edges aligned with those offairing as indicated by arrows. 4) Attach template to fairing using adhesive tape where shown. 5) Punch mark centers of four holes with a
drift and hammer. 6) Drill 6 mm holes through marked centers. To obtain a more balanced response with richer, deeper bases, drill two 50 mm holes in the fairing so as to link the speaker box with the inside of the fairing. Fig. 11-1
—Power amplifier mounting holes- 7) Drill two 5.5 mm holes through concaves in fairing. Fig. 11-2 RIGHT HAND SHOWN, LEFT SIMILAR ADHESIVE TAPE

Incoming search terms:

2009 – Current Harley Davidson Trike Conversion Kit INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 27-02-2012

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the ¼ – 20 Phillips head screw and Seat. 6. Disconnect and REMOVE battery. 7. Remove two ¼ – 20 flanged hex nuts from the Stud Plate. Remove and save the Passenger Handrail and two ¼ – 20 flanged hex head nuts if equipped. 8. Remove the Saddle Bags. 9. Remove the Right and Left Side Covers. 10. Remove Inner Tour Pak Molded Liner. 11. Disconnect the Tour Pak wiring. 12. Remove four ¼ – 20 HHCS. 13. Remove Tour Pak from Top Support Tube. 14. Remove both saddlebag support rails. 15. Loosen Muffler Clamps on both Mufflers and remove two 5/16 – 18 HHCS per Muffler. Remove and discard both Mufflers. Save Muffler Clamps. 16. Remove right side rear heat shield. 17. Remove and discard Muffler Support Plates. 18. Disconnect the Rear Lamp Wiring Harness and remove from T-stud Clip. 19. Remove four frame cover fasteners and the Left and Right Frame Covers. 20. Remove four Tour Pak Support fasteners and the Tour Pak Support.
7 21. Remove four rear fender fasteners and rear fender. 22. Remove four ½ – 13 HHCS and washers. Remove and discard Rear Air Shocks, Air lines and Air Valve bracket. 23. NOTE: NOTE: NOTE: NOTE: If motorcycle is A.B.S. Equipped refer to A.B.S. Installation Instructions. WARNING: WARNING: WARNING: WARNING: If A.B.S. Equipped DO NOT drain brake fluid. 24. Drain all Brake Fluid from the Rear Brake System. 25. Cut and remove Cable ties and un-clamp Wire Harness Loops from the Rear Brake Line along its length, including Clamps on Swing Arm. 26. Remove and discard Banjo Bolt and Crush Washers on Rear Brake Caliper. 27. Remove the Spring Clip and nut from the Rear Axle. 28. Remove Rear Axle and Rear Wheel Spacers. 29. Push Rear Wheel Assembly forward and slip Rear Belt off of the Rear Sprocket. 30. Remove Rear Brake Caliper. 31. Remove and save the two Retaining Washers from the Stud Plate. Remove and save the Stud Plate. 32. Remove Rear Wheel Assembly. 33. Remove two 3/8 – 16 SHCS. Remove Passenger Footboards.

GL 1800 led fairing lights INSTALLATION

0

Filed Under (Honda) by admin on 27-10-2010

download
steP 1 Read and understand all steps in the instructions before starting the installation. Park the motorcycle on a hard, level surface and turn off the ignition. ATTENTION! A factory service manual may be helpful in performing this installation. Do not attempt to perform this installation if you are not confident in your ability to complete all of the steps in the procedure; consult a trained technician. steP 2 Remove the side cover on the clutch side as shown in PIC. 1, by gently pulling on it to release the bosses securing the cover. steP 3 Carefully remove the clutch side fairing-molding piece shown in PIC.2 starting at the bottom of the molding; pulling out to disengage the tabs, working your way up the piece. steP 4 Open the clutch side fairing pocket lid, and remove the four trim clips by pushing in on the center pins, and then pulling the clips out. Set the trim clips aside, as they will be used to reinstall the fairing pocket. (PIC.3) steP 5 Remove the fairing pocket by pulling it straight up and out. steP 6 Remove the rubber grommet from the bottom of the fairing pocket and set aside for now. (See PIC.3.) steP 7 Remove the three bolts from the front fairing as shown in PIC.4; set them aside to reinstall later. steP 8 Remove/disconnect the inline fuse on the power wire (red) and insert through the hole in the bottom of the fairing pocket, so that the controller switch will be located in the fairing pocket. steP 9 Carefully insert the remaining wires one at a time, from the control switch through the hole in the bottom of the fairing pocket.

HARLEY DAVIDSON MULTI-POCKET FAIRING POUCH KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
INSTALLATION 1. Remove the three outer fairing screws located just below the windshield and remove the windshield. 2. See Figure 1 or Figure 2. Apply adhesive pads to the bottom of the bracket in the locations shown. When the bracket is installed, the pads should rest on the top of the inner fairing and support the bracket. 3. Apply clear tape between the screw opening at the base of the windshield on the inside surface of the windshield. 4. See Figure 3. Pull the outer fairing away from the inner fairing to provide sufficient clearance to slide the mounting tabs of the bracket over the top lip of the inner fairing. 5. Center the fairing bracket along the top of the inner fairing. 3 1 2 is04616 1. Bracket 2. Pads 3. Bracket clips Figure 1. Bottom of 3-Pocket Fairing Pouch Over tightening windshield fasteners can crack windshield and/or fairing. (00451b) 6. Reinstall the windshield and three screws removed in Step 1. Tighten screws snugly, but be careful not to over-tighten screw or the fairing may crack. 3 1 2 is04615 1. Bracket 2. Pads 3. Bracket clips Figure 2. Bottom of 2-Pocket Fairing Pouch 4 2 6 5 1 3 is04614 1. Pouch 2. Windshield 3. Tape, clear 4. Outer fairing 5. Pouch bracket clip 6. Top of inner fairing Figure 3. Fairing Clip Attachment, Side View

Incoming search terms:

Harley-Davidson Softail Conversion Kit Installation Instructions

0

Filed Under (Harley Davidson) by admin on 02-12-2010

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the fasteners that secure the seat. Remove seat. 6. Disconnect negative Battery Terminal. 7. Remove the Saddle Bags. And their hardware. If equipped. 8. Loosen Muffler Clamp on both Mufflers and other attaching hardware. Remove and discard both Mufflers. 9. Loosen the 4 exhaust stud nuts and save. Remove and discard head pipes and exhaust gaskets. 10. Disconnect the Rear Lamp Wiring Harness. 11. Remove any fasteners from Electrical Box. 12. Remove and discard Rear Fender, Fender Support and fasteners. NOTE: 2008-Current various models. Remove ECM from Fender and save nuts. 13. Drain all Brake Fluid from the Rear Brake System. 14. Un-clamp Rear Brake Line from the frame and Rear Fork. 15. Remove and discard both Banjo Bolts and Crush Washers from the Rear Brake Caliper and the Rear Brake Master Cylinder. 16. Remove Brake Light Switch from the Brake line, Save for reassembly. 17. Remove the Torx screw from the Brake Line bracket, Save the Torx screw for reassembly. 18. Remove and Discard Brake Line. 19. If Lower Controls option. Remove and Discard right and left floorboards/foot pegs, brake pedal, shifter, and shift linkage. Remove and Discard Passenger Foot pegs or Floorboards and their mounts. Then skip to step 24. 20. If Lower Controls Not purchased. Continue. 21. Remove acorn nut from Shift Linkage. 22. Remove 3 fasteners from Drivers Floorboard and remove. 23. Remove and discard Jiffy Stand. 24. Remove the Primary Cover by first removing the top and rear inspection cover screws. 25. Continue by removing remaining fasteners. 14 total. 26. Remove and discard Primary Cover Gasket. 27. Clean residual gasket material from both surfaces. 28. Loosen the Top Center Nut on the Primary Chain Adjuster. Lower the Primary Chain Adjuster until it rests flat on the Inner Primary Cover. 29. Remove the Clutch Lifter Retaining Ring from the Clutch Basket. Remove Clutch Lifter Assembly. 30. Using the Primary Drive Locking Tool. Loosen the Compensating Sprocket Nut. 31. Using the Primary Drive Locking Tool. Loosen the Clutch Hub Main shaft Nut. WARNING: This nut is LEFT HAND threaded. 32. Remove the Primary Drive Locking Tool, Compensating Sprocket Nut, and Clutch Hub Main shaft Nut. 33. Remove the Sprocket cover and Sliding Cam from the Crank Shaft Extension. 34. Remove the Clutch Assembly, Primary Chain, Compensating Sprocket, and Crank Shaft Extension in one assembly.

HARLEY DAVIDSON ILLUMINATED CHROME COVER KIT FOR FAIRING MOUNT MIRRORS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
INSTALLATION Preparation Models with main fuse: To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the service manual and follow the instructions given to remove the main fuse. Models with main circuit breaker: To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the service manual and follow the instructions given to remove the seat and disconnect the negative (black) battery cable from the negative (-) battery terminal. Retain all seat mounting hardware. Installation NOTE Cover the work surface with an H-D Service Cover or clean shop towels to prevent scratching the finish of the outer fairing. 1. Remove the outer fairing per the instructions in the service manual. Lay the fairing face down on a sturdy work sur- face. 2. See Figure 2. Remove the mirrors (2), flange nuts (3) and plastic backing plates (4) securing the mirrors to each side of the inner fairing (1), and retain all items 3. Measure one inch (25 mm) straight down (5) from the large mirror stud hole in the inner fairing, and make a mark. 4. Drill a 1/4 inch (6 mm) diameter hole (6) through the inner fairing at the mark. 5. See Figure 1. Obtain a chrome wire collar (3) from the kit, and press it into the new hole from the outside of the inner fairing. Gently tap into place with a soft-faced hammer. 6. Repeat Steps 3 through 5 on the opposite side of the inner fairing. NOTE Ambient temperature should be at least 50 °F (10 °C) for proper adhesion of the mirror cover to the mirror. 7. Clean the back surface of the mirrors with the alcohol pad (7) provided. Allow to dry thoroughly. 8. Obtain the primer tube (8) from the kit, and follow the instructions on the tube to activate the primer. When the primer is activated apply the primer to the back surface of one mirror. 3 6 2 1 4 5 is06091 1. Inner fairing 2. Fairing mount mirror 3. Flange nut (2) 4. Plastic backing plate (2) 5. Measure one inch (25 mm) down 6. Drill 1/4 inch (6 mm) hole (2) Figure 2. Fairing Drill for Illuminated Mirror NOTE The Illuminated Chrome Mirror Covers are side-specific. The covers install with the wire harness exiting from the bottom. 9. Obtain the correct mirror cover from the kit. Rub the liners on the three pads on the back surface of the mirror cover to activate the adhesive, then remove the liners. 10. Place the mirror cover over the back surface of the mirror and press into place for a minimum of 60 seconds. 11. Repeat Steps 8 through 10 for the remaining mirror and cover. NOTE The plastic backing plates (removed earlier) are identified with a letter “L” (left) or “R” (right) stamped on the post. The mirrors are marked with a letter “L” or “R” stamped on the swivel block. Use the correct backing plate for each mirror by matching the letters. 12. Position the mirror on the outer face of the inner fairing, with the rounded side of the mirror outboard and the Bar & Shield logo upright. a. Insert the mirror cover wiring harness through the chrome wire collar installed in Step 5. b. Insert the mirror post through the original mirror mounting hole. c. Place the correct plastic backing plate against the inner face of the inner fairing, engaging the two holes in the backing plate with the threaded stud and index pin on the mirror swivel block. d. Install the flange nut on the threaded stud and tighten to 30-40 in-lbs (3.4-4.5 Nm) . e. Repeat for the remaining mirror on the other side of the fairing

Incoming search terms:

HARLEY DAVIDSON FAIRING MOUNT MIRRORS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-02-2011

download
INSTALLATION Removing Outer Fairing 1. Standing at the front of the vehicle, use a T-27 TORX® drive head to remove the three outer fairing screws (with flat washers) just below the windshield. 2. Moving to the inner fairing side, use a T-27 TORX drive head to remove the two fairing screws just above the wind deflectors on the left and right side. 3. Turn the handlebar to the right and remove the outer fairing screw (reach in below the fairing cap). Turn the handlebar to the left and remove the fairing screw on the opposite side. 4. Tilting the outer fairing toward the front, squeeze the two external tabs to remove the wire connector at the back of the headlamp assembly. 5. Lift the fairing (with headlamp assembly) off the motor- cycle. NOTE Since the outer fairing screws hold the windshield in place, the windshield may fall to the floor if not removed. 6. Remove the Windshield. Installing Mirrors 1. See Figure 1. Place template on inside of fairing as shown to locate mounting holes for mirror. 2. Begin by drilling a 1/8 inch pilot hole at each location marked on the template. For the center hole (2) where the 3/8 inch threaded stud passes through the fairing use a 13/32 inch diameter twist drill to drill the hole to its final size. For the alignment hole (1), use a 7/32 inch diameter twist drill to drill the hole to the final size. 2 1 is 02115 1.7/32 inch hole location 2.13/32 inch hole location Figure 1. Positioning Template 1 is06315 1. Auxiliary mirror Figure 2. Orientation of Auxiliary Mirror NOTE The flange nut is a self locking nut and must not be tightened more than 30 in-lbs (3.4 Nm). 3. See Figure 3. Place mirror (2) in position and install backing plate (4) with the raised post (B) (with the L and R marking) toward the nut surface. Install the flange nut (6) and tighten nut to 20-30 in-lbs (2.3-3.4 Nm). 4. See Figure 2. Position the mirror so the round auxiliary mirror is in the upper inside corner position. 5. Repeat for right side

GL 1200 CB TRANSCEIVER Installation Manual

0

Filed Under (Honda) by admin on 21-11-2011

download
Remove the right and left side covers. Disconnect the battery negative cable from the battery negative terminal.
2) Remove the left fairing pocket Remove the Auto volume control unit. -1 Remove the CB blind cover from the fairing by removing the four 5 x 22 mm socket head bolts. (Fig. 2) Disconnect the three wire connectors of the auto volume unit. (Fig. 3) -2 Remove the two 4 x 12mm tapping screws and remove the knob and nut from the auto volume control unit. (Fig. 1) -3 Remove the bracket form the auto volume control unit. NOTE: Discard the CB blind cover, 4 x 22mm tapping screws, and bracket. 4) Remove the seat. 5) Remove the shelter NOTE: To remove the front of the shelter, it is necessary to remove the inner cover by lifting the rear of the cover. 6) Remove the two tapping screws attaching the left coupler cover and move the holder towards the center. 7) Remove the main amplifier. -1 Disconnect the main amplifier 2-P black connector. -2 Straighten the four wire clamps at the main amplifier to release the harnesses. -3 Remove the two nuts and washers holding the main amplifier; pull the amplifier out between the left fairing pocket and handlebar by pulling up on the bottom. 8) Connect the two DIN connectors if the transceiver harness (65) to the terminal component (62) color-to-color (Fig. 7). 9) Remove the seals from the terminal component mounts inside the fairing. Position the terminal component (62) on the mounts and install using cap nuts (69) and washers (72). NOTE: Use care when installing the terminal component (62) not to push in the audio harness, CB harness and terminal component harness into the fairing pocket

Incoming search terms: