fuel pump removal r1200gs bmw

You search Auto repair manual PDF fuel pump removal r1200gs bmw, if there are search results will appear below. If search results do not exist, please search by others keyword.



  fuel pump removal r1200gs bmw Direct Download speed 5282 Kb/s

  fuel pump removal r1200gs bmw Full Version speed 6162 Kb/s



YAMAHA Road Star Fuel Pump Relocation Kit INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 08-11-2010

download
1. Remove seat and disconnect battery. Remove fuel tank along with both left and right side battery covers, and remove air box from carburetor (all per Yamaha standard shop manual procedures). 2. Remove chrome plastic cover over fuel pump and disconnect choke cable/knob from lower pump bracket. Remove pump-to-carb fuel line from fuel pump. Disconnect fuel pumps electrical lead connector. 3. Remove two (2) hex-head pump mounting bracket bolts and remove pump assembly from motorcycle. Slide fuel pump up and off bracket mounting posts (Caution: excess fuel may drain from pump and/or fuel lines and fuel filter!). Remove heat shield. Remove remaining fuel line from pump. Pull all fuel lines from filter and remove steel springs and hose clamps from these lines (these will be reused on the kits fuel lines). With a sharp knife or box cutter, trim off the top portion of the fuel pumps rubber isolation/mount system per Photo A. Next cut pumps wiring harness approximately half way between connector and pump. Strip the insulation from the ends of these wires as well as from the supplied Baron harness extension wires. Using the supplied electrical butt connectors, crimp Baron harness extensions red wire to pumps black-w/blue-strip wire, and Baron harness extensions black wire to pumps black wire. Repeat this process on other side of wire harness extension with pumps connector. Now, referring to Photo B, you will need to cut off the square tube that runs along the side of the fuel pump with a hack saw. Cut down toward pump body in a straight cut, then cut tube off by cutting along the body. This will allow you to twist pump in the rubber mount so the curved spigot is facing up (clockwise approx 1/4 turn). 4. Remove pump-to-carb fuel line from carb and separate electrical wires from this line. Remove this fuel line from engine. Re-route choke cable to right side of engine (toward carb) and rotate it up and over rear cylinder head back toward left side of bike. Mount new Baron choke bracket to the choke cable and tighten plastic nut. New choke bracket will mount to rear fuel tank mounting location (Photo C). 5. 99~03 models – Remove electrical relay bracket (found under the right side cover) from the bike and slide each relay off of this bracket. Install fuel pump onto new Baron Fuel Pump Bracket and install bracket in the same location as the stock bracket you just removed, using stock mounting hardware. Refer to Photo F for proper installation. 6. 04~07 models Remove electrical relays from stock bracket and remove relays from rubber holder. Cut rubber holder per Photo E and replace one of the relays into the rubber and install on to new Baron bracket. The second relay will be placed to the right of the tool bag under the seat and secured with the provided two-sided tape pad. Reconnect plugs to the relays. (Photo F)

2003 SUZUKI SV 650 FUEL SYSTEM AND THROTTLE BODY SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
FUEL PUMP The electric fuel pump is mounted at the bottom of the fuel tank, which consists of the armature, magnet, impeller, brush, check valve and relief valve . The ECM controls its ON/OFF operation as controlled under the FUEL PUMP CONTROL SYSTEM . When electrical energy is supplied to the fuel pump, the motor in the pump runs and together with the impel- ler . This causes a pressure difference to occur on both sides of the impeller as there are many grooves around it . Then the fuel is drawn through the inlet port, and with its pressure increased, it is discharged through the outlet port . The fuel pump has a check valve to keep some pressure in the fuel feed hose even when the fuel pump is stopped . Also, the relief valve is equipped in the fuel pump, which releases pressurized fuel to the fuel tank when the outlet of the fuel pressure has increased up to 450 -600 kPa (4.5- 6.0 kgf/cm2,64- 85 psi) . Relief valve Brush , ∎ I,’ Check valve Magnet L Armature When the impeller is driven by the motor, pressure differential occurs between the front part and the rear part of the blade groove as viewed in angular direction due to fluid friction . This process continuously takes place causing fuel pressure to be built up . The pressurized fuel is then let out from the pump chamber and discharged through the motor section and the check valve . FUEL SYSTEM AND THROTTLE BODY 5- 3 Inlet port I I Impeller 5-4 FUEL SYSTEM AND THROTTLE BODY FUEL PRESSURE REGULATOR The fuel pressure regulator consists of the spring and valve . It keeps absolute fuel pressure of 300 kPa (3.0 kgf/cm2,43 psi) to be applied to the injector at all times . When the fuel pressure rises more than 300 kPa (3 .0 kgf/cm2, 43 psi), the fuel pushes the valve in the regulator open and excess fuel returns to the fuel tank . 90 Spring 02 Valve FUEL INJECTOR The fuel injector consists of the solenoid coil, plunger, needle valve and filter . It is an electromagnetic type injection nozzle which injects fuel in the throttle body according to the signal from the ECM. When the solenoid coil of the injector is energized by the ECM, it becomes an electromagnet and attracts the plunger. At the same time, the needle valve incorporated with the plunger opens and the injector which is under the fuel pressure injects fuel in conic dispersion . As the lift stroke of the needle valve of the injector is set constant, the volume of the fuel injected at one time is determined by the length of time during which the solenoid coil is energized (injection time)

2007 Softail HARLEY DAVIDSON FUEL PUMP/ FUEL GAUGE SENDING UNIT REMOVAL AND INSTALLATION

0

Filed Under (Harley Davidson) by admin on 30-03-2012

download
1. Remove seat. 1 WARNING 1 WARNING To prevent spray of fuel, purge system of high-pressure fuel before supply line is disconnected. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00275a) 2. Purge the fuel supply line of high pressure gasoline. a. See Figure 4-36. Disconnect the fuel pump fuse from the main wiring harness. b. Start the engine and allow the vehicle to run. c. When the engine stalls, operate the starter for 3 seconds to remove any remaining fuel from the fuel lines. 1 WARNING 1 WARNING To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 3. Disconnect negative battery cable. 4. Remove instrument console. a. All but FXSTD, see Figure 4-37. Remove acorn nut and washer on instrument console to separate console from fuel tank. b. For FXSTD, see 8.26 INSTRUMENT CONSOLE: FXSTD. 5. Disconnect console wiring. Figure 4-36. Fuel Pump Fuse: View From Top Figure 4-37. Acorn Nut And Washer: All But FXSTD s0660x8xx 7526
4-28 2007 Softail: Fuel System HOME 1 WARNING 1 WARNING Gasoline can drain from the crossover line when disconnected from fuel tank. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. Wipe up spilled fuel immediately and dispose of rags in a suitable manner. (00259a) 6. Drain fuel tank. a. Obtain a short section of hose (5/16 inch I.D.). Insert bolt in one end of hose and install hose clamp to ensure that end is securely plugged. b. See Figure 4-38. Cut clamp (1) from one end of crossover hose (2). Quickly replace crossover hose on fuel tank fitting with open end of short hose while directing flow of gasoline from free end of crossover hose into suitable container. 7. See Figure 4-39. Unplug fuel pump module connector (3) [86]. 8. Remove top plate screws (2) and discard. 9. See Figure 4-40. Pull top plate (2) out of fuel tank enough to expose fuel hose and clamp (1). CAUTION Carefully inspect end of hose for cuts, tears, holes or other damage. Replace hose if any damage is found. Even the smallest hole can cause a reduction in fuel pressure. 10. Cut clamp and remove hose from regulator housing fit- ting.

2001-2003 XV16 Fuel Pump and Carburetor Removal

0

Filed Under (Yamaha) by admin on 31-12-2011

download
Disconnect the carburetor fuel line hose at the fuel pump. •Disconnect the fuel pump wire coupler. •Remove the choke cable from fuel pump bracket. •Remove the upper engine mount, leaving the fuel pump attached to the mount. •Disconnect the TPS and carburetor wire couplers.       Disconnect the throttle cables, and then remove the carburetor. NOTE: The idle adjuster can be removed from its bracket without loosening the bracket screws. PAGE 3 of 12 HIDDEN 6mm SCREW 6mm BOLT UPPER ENGINE MOUNT/ FUEL PUMP CARBURETOR PAGE 4 of 12 Right-Hand Footrest Removal: •Disconnect and remove the brake light switch. •Remove the forward-most tie wrap around the brake hose and frame. •Remove the footrest assembly. NOTE: Leave the brake hose attached. Move the hose to the underside of the foot rest mount and support it as necessary so that it is out of the way Cylinder Head Oil Pipe Removal/ Installation: •Slightly loosen all three banjo bolts before removing them to prevent oil line deformation. NOTE: When loosening the upper banjo bolts, hold the line in place using a wrench at the flat surface on the fitting. Air Injection System (AIS) Removal: •Remove the electric starter motor. •Remove the regulator/rectifier assembly. Remove the AIS pipes from the cylinder head, but leave them attached to the AIS assembly. •Remove the three screws with 8mm heads, and then remove the AIS air filter from the right side. •Remove the three Phillips head screws holding    the AIS assembly on the frame. •Remove the AIS assembly from the left side. FOOTREST ASSEMBLY UPPER BANJO BOLT AIS AIR FILTER AIS ASSEMBLY
PAGE 5 of 12 Transfer Case Removal: •Remove the transfer case bracket first. Then remove the outer chrome cover, inner cover, and drive-sprocket nut. NOTE: There is a sealing washer between the inner case and the transfer case at the 8mm stud. Be sure to replace it during re-assembly. •Remove the two chrome oil lines between the engine and oil tank. NOTE: Retain the four O-rings for re-use. •Remove the drive pulley cover and remove the drive pulley nut. •Loosen the drive belt tension. •Remove the drive pulley, inner cover, collar, and O-ring. NOTE: The collar has a bevel on its inside diameter     for the O-ring facing inward and a bevel on the outside diameter facing the pulley. •Remove the drive and driven sprockets with chain as an assembly. •Remove the collar and O-ring. NOTE: Collar has a bevel on its inside diameter that faces inward for the O-ring. •Remove oil tank filler neck. •Remove the relay bracket on the right-hand side. NOTE: Leave the relays connected. Simply move them out of the way to allow room for transfer case removal. •Slide the transfer case out from the right side.

HARLEY DAVIDSON FUEL LEVEL SENDER ADAPTER BRACKET KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 28-02-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the Service Manual and follow the instructions given to remove the main fuse. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 2. Remove the currently installed fuel tank from the vehicle. Follow the instructions for the correct model vehicle under FUEL TANK: EFI, REMOVAL in the Service Manual. 3. See FUEL PUMP/FUEL GAUGE SENDING UNIT, REMOVAL in the Service Manual for instructions to: a. Unplug the fuel pump module connector. b. Remove and discard the top plate screws. c. Remove the top plate, fuel pump and fuel level sender (fuel gauge sending unit) from the tank. NOTE Take care to avoid bending the fuel level sender float rod. A bent float rod will lead to erroneous gauge readings. 2 6 1 3 4 7 9 8 5 is05284 1. Fuel level sender 2. Electrical grounding tab 3. Fuel level sender lock tab 4. Adapter bracket 5. Slot (2) 6. Terminal strip insert 7. Sender to adapter lock tab 8. Slider 9. Adapter to tank lock tab Figure 1. Fuel Level Sender Assembly to Adapter – 4. See Figure 1. Clean the electrical grounding tab (2) on the back of the fuel level sender if necessary. The tab must make firm contact with the terminal strip insert (6) in the adapter bracket. Slide the original equipment (O.E.) fuel level sender (1) into the slots (5) in the new adapter bracket (4) as shown until the lock tabs (3 and 7) snap into place. Make sure the wire is not pinched between the adapter and sender. 5. See FUEL SUPPLY CHECK VALVE/TUBE in the Service Manual. Remove the check valve/quick-connect fitting assembly from the old fuel tank, and assemble to the new tank, using a new O-ring (purchased separately). 6. Fit the slider (8) on the adapter bracket into the fuel level sender mounting channel inside the tank, and push down until the lock tab (9) snaps into place. Make sure the sender and adapter wires are not pinched between the adapter and the fuel tank tunnel, and remain accessible through the fuel tank top opening. 7. See Figure 2. Obtain the assembly of the top plate (1), regulator (2) and fuel filter (3) removed from the old fuel tank, and the stainless steel screw (8) and nut (9) provided in this kit.

Related Item : what fuel sending unit fits a 2001 harley fxdl (2)writing diagram tank urban 50 scooter (1)removal of gas tank gsxr (1)r850r gas tank removal (1)leaking harley fuel top plate (1)large motorcycle tanks 1100 ACE handa (1)install plastic fuel tank valve (1)how to remove gsxr 750ngas tank (1)how to remove 2014 ktm 350 gas tank (1)how to empty gas from a scooter (1)