2011 triumph america motorcycle owners manual

You search Auto repair manual PDF 2011 triumph america motorcycle owners manual, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2011 triumph america motorcycle owners manual Direct Download speed 5282 Kb/s

  2011 triumph america motorcycle owners manual Full Version speed 6162 Kb/s



2002-2004 TRIUMPH BONNEVILLE AMERICA/ SPEEDMASTER CARBURETOR KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 28-10-2010

download
A.) REAR WHEEL REMOVAL- PAGE 14-16 Triumph Motorcycle Service Manual 1.) Support motorcycle on center stand or center lift so rear wheel is suspended and there is clearance for removal. Use tie downs. 2.) If both wheels are raised chock the front wheel to prevent any weight shift when rear wheel is removed. 3.) Remove chain guard. 4.) Remove caliper and support so there is no strain on the brake line. 5.) Remove both silencers from exhaust headers. 6.) Remove axle nut and washer—support or chock rear wheel—and slide out axle. 7.) Disengage chain from sprocket and hang over swing—use soft cloth to protect swing arm from scratches that will occur if you do not cover. 8.) Lower wheel to the ground and collect spacer and caliper support arm and all fasteners for re-assembly. B.) REMOVE SEAT PAGE 15-9 Triumph Motorcycle Service Manual 1.) Remove the 12 mm bolt from rear seat section—if you have a pillion pad remove it first by removing the 8 mm bolt, slide forward and lift free of seat catch. Take a position where you can see what you are doing or you will scratch your painted surface. 2.) Lift seat from the rear and slide backwards to disengage tongue– collect all fasteners for re-assembly. C.) REMOVE REAR MUD GUARD PAGE 15-14 Triumph Motorcycle Service Manual 1.) Disconnect battery and remove from motorcycle. 2.) Disconnect electrical connectors on the underside of the mudguard. 3.) Support fender from beneath and remove the 4 side allen head mount bolts and 2 12mm hex head top front mount bolts– collect all fasteners for re-assembly. D.) REMOVE FUEL TANK PAGE 9-11 Triumph Motorcycle Service Manual 1.) Turn off fuel tap. 2.) Remove fuel line at the tap connection. 3.) Remove the 12mm rear tank-mounting bolt. 4.) With assistance from another set of hands support tank at the rear and lift so that the breather line is visible on the right side of the underside of tank—remove and plug line. 5.) With tank raised and supported at the rear slide backwards— disengaging it from the front mounting rubbers—set tank aside in a safe place to prevent any damage to the painted surface. E.) REMOVE SIDE COVERS PAGE 15-10 and 9-15 Triumph Motorcycle Service Manual 1.) Loosen and remove left side cover screws on the air filter facade— lift slightly to disengage top mounts and remove—set aside in a safe place to prevent damage to painted surface. 2.) On right side cover simply and gently pull bayonet fittings from rubber slip mounts. 3.) Secure these rubber mounts and remove for later re-assembly with the Bonneville Performance brackets.

Triumph America Installation Manual

0

Filed Under (Triumph) by admin on 29-10-2010

download
Secure motorcycle in an upright position. 2) Remove center stand 3) Remove saddle bags (if applicable) 4) Attach bracket A to center stand mounting point on motorcycle 5) Attach bracket D (left) / E (right) to rear fender sub-frame using new bolts provided. It may be necessary to reattach saddle bags at this point 6) Attach bracket F (left) / G (right) to rear of brackets D/E. 7) Attach bottom of brackets F/G to rear hitch plate. 8) Attach bracket B (left) / C (right) to bottom of forward hitch arms. Attach other end of B/C to top of bracket A. 9) Ensure hitch is square with motorcycle and tighten all bolts. Receiver Hitch Diagram Leveling stand screw jack installation 1) Thread right side screw jack into threaded leveling stand tab on bracket A and adjust leveling jack bolt out. 2) Push motorcycle over from left side until right screw jack is touching floor. 3) Install left side screw jack on bracket A and adjust out until motorcycle will rest upright on both screw jacks. 4) Adjust screw jacks until motorcycle is level. CAUTION – Use screw jacks to hold motorcycle upright and level ONLY. Do not lift motorcycle with screw jacks. CAUTION – Use care when installing screw jacks. Be certain that motorcycle is always in a stable balanced position

2005-2007 KTM MOTORCYCLE REPAIR MANUAL

0

Filed Under (KTM) by admin on 21-11-2010

download
Adjustments -Take notice of the position of the compression adjustment 1 ! -Count the amount of clicks by turning the adjustment screw clockwise till fully closed. -Remove the rubber cap out of the axleclamp. -Take notice of the position of the rebound adjustment 2 ! -Count the amount of clicks by turning the adjustment screw clockwise till fully closed. -For the standard position see setting list. Position of the compression and rebound adjustment -Set the rebound position 1 , see KTM-Owners manual. -Assemble the rubber cap. -Set the compression position 2 , see KTM-Owners manual. 1 2 2-22 Repair manual WP Fork “Closed Cartridge” Art.No.: 3.211.199-E Explanation of the spring preload -Total spring length without the spacers, see chapter inspection of the spring! -Spring length with spacers 1 , see setting list. -Spring with the spacers. 1 . -The spring is assembled in the front fork leg. NOTE: the distance of “B” is less then the length of “A”. A – B = Spring preload A 1 1 B 2-23 Air release screw -Place the motorcycle on the stand. NOTE: the front wheel must be lift of the floor! -Unscrew the air release screw 1 of the screw cap on top of the front fork and tighten after approx. 10 seconds the air release screw. Recommended periodic maintenance and inspection of the 4860 SX/SXS/SMR front fork 1 A 100 liter fuel consumption is equivalent to approx. 15 operating hours Clean dust scrapers (after 1 hour) Bleed fork legs regularly – after every cleaning Check the inner tubes on scratches / leakage Visual check of damaging of the outer-tubes / replace if necessary Complete service without disass. the closed cartridge of the fork Complete service including the closed cartridge of the front fork Dismounting the fork -Place your motorcycle on a stand. -Notice the position of the front fork in the triple-clamps. NOTE: To remove the front fork. Read your KTM Instruction Manual or Workshop Manual. 3-3 Mounting the fork -Clean the innerside of the triple-clamps with brake cleaner. -Slide both fork legs into the triple-clamps. NOTE: Pay attention to the position of the fork legs. Standard riding height! NOTE: The maximum riding height is the level of the second groove! -Tighten the middle bolt of the lower triple clamp to a torque of 17 Nm! -Tighten the first bolt of the lower triple clamp to a torque of 17 Nm! -Tighten the third bolt of the lower triple clamp to a torque of 17 Nm!

Honda CG125 Owners Manual, and repair manual

0

Filed Under (Honda) by admin on 11-12-2011

download
The author of this manual has the conviction that the only way in which a meaningful and easy to follow text can be
written is first to do the work himself, under conditions similar to those found in the average household. As a result, the hands seen in the photographs are those of the author. Even the machines are not new: examples that have covered a consider- able mileage were selected so that the conditions encountered would be typical of those found by the average owner. Unless specially mentioned, and therefore considered essential, Honda service tools have not been used. There is
invariably some alternative means of slackening or removing some vital component when service tools are not available and
isk of damage has to be avoided at all costs. Each of the six Chapters is divided into numbered Sections. Within the Sections are numbered paragraphs. In consequence, cross reference throughout this manual is both straightforward
and logical. When a reference is made ‘See Section 5.12′ it means Section 5, paragraph 12 in the same Chapter. If another
Chapter were meant, the text would read ‘See Chapter 2, Section 5.12′. All photographs are captioned with a Section/paragraph number to which they refer and are always relevant to the Chapter text adjacent. Figure numbers (usually line illustrations) appear in numerical order, within a given Chapter. Fig. 1.1 therefore refers o the first figure in Chapter 1. Left-hand and right-hand descriptions of the machines and their component parts refer to the right and left of a given machine when the rider is seated normally. Motorcycle manufacturers continually make changes to specifications and recommendations, and these, when notified,mare incorporated into our manuals at the earliest opportunity.
We take great pride in the accuracy of information given in this manual, but motorcycle manufacturers make alterations and design changes during the production run of a particular n motorcycle of which they do not inform us. No liability can be ccepted by the authors or publishers for loss, damage or injury caused by any errors in, or omissions from, the information give

Daytona 675 Motorcycle Race Kit Installation Manual

0

Filed Under (Triumph) by admin on 29-10-2010

download
Remove the existing cylinder head gasket in line with the procedures detailed in the Daytona 675 service manual. 2. Fit the chosen race kit cylinder head gasket following the procedures detailed in the Daytona 675 service manual. Caution The use of the following race kit cylinder head gaskets will require changes to the fuelling settings. To alter fuelling settings a third party programmable control unit will be required. Item Description Qty 1 Head gasket (t = 0.65mm) 1 1 Head gasket (t = 0.60mm) 1 1 * Page 7 of 29 © Triumph Designs Ltd 2007. Cams, Valve Spring & Sprocket Kits Parts Supplied Camshaft Inlet Kit – A9618055 Camshaft Exhaust Kit – A9618056 Valve Spring Kit – A9618058 Camshaft Sprocket Kit – A9618057 Warning The race kit must be fitted as a complete set. If it is not fitted as a complete set a failure may result which could cause loss of motorcycle control and an accident. Caution The use of the Camshaft, Valve spring & Sprocket race kits detailed below will require changes to the fuelling settings. To alter fuelling settings a third party programmable control unit will be required. 5 5 4 1 3 2 4 3 Item Description Qty 1 Cam assy, inlet, race 1 Item Description Qty 2 Cam assy, exhaust, race 1 Item Description Qty 3 Valve spring, 14.4id, race12 Item Description Qty 4 Sprocket, camshaft, 34T 2 5 Socket head cap screw, Encapsulated, M6x10 4
Page 8 of 29 © Triumph Designs Ltd 2007. NOTE •The standard inlet cam is 9.25mm max lift and 258.50o duration. The race kit inlet cam is 9.25mm max lift and 268.74o duration. •The standard exhaust cam is 8.5mm max lift and 246o duration. The race kit exhaust cam is 8.5mm max lift and 262.21o duration. •The race kit valve spring must be used in conjunction with the standard spring platforms and retainers. The fitted length of the race springs is the same as the standard spring. 1. The race kit valve springs should be assembled in the same manner as the standard valve springs. Follow the procedure detailed in section 3 of the Daytona 675 service manual. Ensure the springs are installed with the close wound, colour coded end of the springs facing downwards, towards the piston. 2. The race kit camshafts should be assembled in the same manner as the standard camshafts. Follow the procedure detailed in section 3 of the Daytona 675 service manual. 3. The race kit cam sprockets should be mounted and secured to the camshafts using the slotted holes in the sprocket. The slotted holes allow adjustment of the valve timing. The circular holes in the sprockets are for Triumph service tool T3880102 and should not be used to mount the sprockets to the camshafts. NOTE •No timing marks are included on the race sprockets. Race engines will typically have different depths skimmed off the cylinder head and, therefore require specific individual timing. 4. The camshafts should be timed using cam degreeing equipment which typically consists of a degree wheel, pointer, dial indicator and piston stop. Optimum cam timing will depend on the exact specification of the engine, but a recommended starting point is 104o IMOP (Inlet Maximum Opening Point) and 104o EMOP (Exhaust Maximum Opening Point). 5. Always check the inlet and exhaust piston to valve clearance for the timing selected to use, before running the engine. You must ensure both clearances are adequate. As a guide, the standard nominal piston to valve clearance is 1.3mm inlet & 1.5mm exhaust

Related Item : 2510 mul3 1995 lift kit (1)vn2000 cam (1)valve timing chain alignment marks for a1962 norton motorcycle (1)triumph trike conversion kits (1)triumph daytona 675 exhaust valve open position (1)tri glide adjustable passenger floor boards (1)show how to install lift kit on tri glide (1)pinion side of twin cam (1)motorcycle cam timing marks (1)kymco mxu 700i le lift kit (1)