2008 ktm 250 xc bolt torque specs

You search Auto repair manual PDF 2008 ktm 250 xc bolt torque specs, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2008 ktm 250 xc bolt torque specs Direct Download speed 5282 Kb/s

  2008 ktm 250 xc bolt torque specs Full Version speed 6162 Kb/s



2008 KTM 250 SX-F 250 XC-F, XCF-W 250 EXC-F, EXC-F SIX DAYS INSTALLATION MANUAL

0

Filed Under (KTM) by admin on 22-10-2010

download
Hand brake lever The hand brake lever [1] is mounted on the handlebars on the right and actuates the front wheel brake. The adjusting screw [A] can be used to change the basic position of the hand brake lever (see “Maintenance”). 1 A Short circuit button The short circuit button [2] turns off the engine. When pressing this button, the ignition circuit is short-circuited. 2 Headlamp switch (XCF-W) In this model the headlamp is switched on with the pull switch [5] . 5 Flasher switch The flasher switch is a separate unit and is mounted on the left portion of the handlebar. The wire harness is designed in a way that whenever you want to use your bike off-road, you can dismount the entire turn indicator system without affecting the function of the remaining electrical system. Flasher left Flasher right
OPERATION INSTRUMENTS » ENGLISH 7 1 2 3 4 5 Starter button Pushing the red starter button [1] will actuate the E-starter. Emergency OFF switch (EXC-F Australia) The red emergency-OFF switch [2] is arranged adjacent to the throttle grip. In this position, the E-starter is operational and the engine can be started. In this position, the E-starter and ignition circuits are interrupted.The E-starter cannot be actuated, and the engine will not start, not even if you attempt to start it with the kickstarter. Pushing the black starter button [3] will actuate the E-starter. Indicator lamps The green control lamp [4] flashes in the same rhythm as the flashing indicator when the indicator is working. The blue control lamp [5] lights up when the high beam is on. TEST All of the display segments briefly light up for the display function test. Electronic speedometer The display in the electronic speedometer is activated as soon as you press a button on the speedometer or an impulse is received from the wheel sensor. The display lights up when the engine is running. The display is cleared if no button is pressed for 1 minute or no impulse is received from the wheel sensor. The button is used to change between display modes. The + and – buttons are used to control various functions

Incoming search terms:

Kawasaki Ninja 250 FAQ

0

Filed Under (Kawasaki) by admin on 15-11-2010

download
Am I too small for this motorcycle? Duke – Sun May 14 17:38:31 2000 I’m only about 5’2″ and don’t have a problem, even though I can only touch the ground with the ends of my toes. Once you get a feel for the balance of the bike it’s not hard to keep everything upright. Only place I have trouble is pushing the bike backwards in a parking lot. Usually I just walk the bike (beside it) to where I can get on and get going. How does the EX500 compare to the EX250? Craig M. – Mon May 22 10:23:29 2000 I have both the EX250 and the EX500; both are Y2K models. The 250 is a screamer that performs well and can easily get me into trouble. My only complaints about the 250 are the excessive nose dive when getting on the front brake hard and the skittishness of the rear during high speed cornering. Both are easily corrected with suspension adjustments, I’ve just been too lazy to get the parts and do the work. A bit more wind protection would be great too. The 500 addresses these problems, the diving of the front end (to a degree); the rear’s skittishness and the wind protection. A plus for the 500 is the greater torque and power off the line; it pulls stronger (in my opinion) and will get you into illegal speed territory just a bit quicker than the 250. With greater weight, is has more stability in high speed and windy situations. Insurance is just about the same for both, with the 250 getting the nod for gas mileage. Service requirements are almost identical for both as well, being that they’re both parallel twins, the technology is the virtually the same. The downfalls of the 500: $2K more than the 250 (can do a lot to the 250 with that kind of money); buzzy mirrors, barely useful; heavier weight to have to push around the garage; lesser gas mileage (55-60 MPG; 250 pushes 70 MPG easily); engine is worse than a nervous dog shaking around at idle and at speed (here the 250 is far superior and much smoother). In my opinion, the 500 is a better suited for a larger rider, from a comfort standpoint. I feel I can stretch out a bit more on it than the 250 (I’m 5′ 9″, 160 lbs). The 250′s brakes are better tuned than the 500 and the shifter is much smoother. That may be due to the 3,500 mile difference between the two bikes. Bottom line, both bikes are great, the 250 is now my wife’s ride (mainly) and the 500′s mine (unless she steals the keys away). In time, I’ll make the adjustments to the 250; she doesn’t push it like I do.

Incoming search terms:

2008 KTM Model Engine Oil Recommendation Chart

0

Filed Under (KTM) by admin on 24-11-2010

download
2008 Model Type Recommended Engine Oil Type Quantity SPORTMINICYCLES AC 50 SX MINI Motorex ATF Super (Dexron II Gear Oil) 0.15-0.2 L SPORTMINICYCLES LC 50 SX JUNIOR Motorex ATF Super (Dexron II Gear Oil) 0.15-0.2 L 50 SX Motorex ATF Super (Dexron II Gear Oil) 0.15-0.2 L 65 SX Motorex Top Speed 4T 15W50 0.5L SX 2 STROKE 85 SX Motorex Top Speed 4T 15W50 0.5 L 105 SX Motorex Top Speed 4T 15W50 0.5 L 125 SX Motorex Top Speed 4T 15W50 0.7 L 144 SX Motorex Top Speed 4T 15W50 0.7 L 250 SX Motorex Top Speed 4T 15W50 0.7 L SX 4 STROKE 250 SX-F Motorex Power Synt 4T 10W50 1.1 L 450 SX-F Motorex Power Synt 4T 10W50 1.35 L 505 SX-F Motorex Power Synt 4T 10W50 1.35 L CROSS COUNTRY 2 STROKE 65 XC Motorex Top Speed 4T 15W50 0.5L 85 XC Motorex Top Speed 4T 15W50 0.5L 105 XC Motorex Top Speed 4T 15W50 0.5 L 200 XC Motorex Top Speed 4T 15W50 0.7 L
200 XC-W Motorex Top Speed 4T 15W50 0.7 L 250 XC Motorex Top Speed 4T 15W50 0.7 L 250 XC-W (e) Motorex Top Speed 4T 15W50 0.7 L 300 XC Motorex Top Speed 4T 15W50 0.7 L 300 XC-W (e) Motorex Top Speed 4T 15W50 0.7 L CROSS COUNTRY 4 STROKE 250 XC-F Motorex Power Synt 4T 10W50 1.1 L 250 XC-F-W Motorex Power Synt 4T 10W50 1.1 L 450 XC-F Motorex Power Synt 4T 10W50 1.35 L 450 XC-W (R) Engine – Motorex Power Synt 4T 10W50 Gearbox – Motorex 4T 10W50 0.7 L 0.9 L 505 XC-F Motorex Power Synt 4T 10W50 1.35 L 530 XC-W (R) Engine – Motorex Power Synt 4T 10W50 Gearbox – Motorex 4T 10W50 0.7 L 0.9 L ENDURO RACING 450 EXC (R) Engine – Motorex Power Synt 4T 10W50 Gearbox – Motorex 4T 10W50 0.7 L 0.9 L 530 EXC (R) Engine – Motorex Power Synt 4T 10W50 Gearbox – Motorex 4T 10W50 0.7 L 0.9 L SUPERMOTO LC4 690 Supermoto Motorex Power Synt 4T 10W60 Approx. 2.0 L SPORT ATV 450 XC Motorex Power Synt 4T 10W50 2.0 L 525 XC Motorex Power Synt 4T 10W50 2.0 L LC8 950 Super Enduro (R) Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 990 Adventure Orange Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 990 Adventure Black Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 990 Adventure S Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 990 Super Duke Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 990 Super Duke R Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L

Incoming search terms:

2008 FLT Police Models Service Manual Supplement

0

Filed Under (Harley Davidson) by admin on 25-11-2010

download
ITEM SERVICED 14-21 ft-lbs (19.0-28.5 Nm) Drain plug torque Engine oil and filter 4 qt. (3.8 L) Oil capacity Hand tighten 1/2-3/4 turn after gasket contact Filter 63798-99A Chrome filter part number 63731-99A Black filter part number FORMULA+ TRANSMISSION AND PRIMARY CHAIN LUBRICATION (Part No. 99851-05) Lubricant type and capacity Primary chain lubricant Wet: 38 oz. (1124 ml) Dry: 45 oz. (1331 ml) 14-21 ft-lbs (19.0-28.5 Nm) Primary chaincase drain plug torque 1/2-1 turn Adjuster screw free play Clutch adjustment 72-120 in-lbs (8.1-13.6 Nm) Adjuster screw locknut torque 1/16-1/8 in. (1.6-3.2 mm) Free play at hand lever 84-108 in-lbs (9.5-12.2 Nm) Clutch inspection cover torque Dipstick at FULL with motorcycle on jiffy stand and filler plug resting on threads. Lubricant level Transmission lubricant FORMULA+ TRANSMISSION AND PRIMARY CHAIN LUBRICATION (Part No. 99851-05) Lubricant type and capacity 32 oz (0.95 liters) 14-21 ft-lbs (19.0-28.5 Nm) Transmission drain plug torque 25-75 in-lbs (2.8-8.5 Nm) Transmission filler plug/dipstick torque Front: 36 psi (248 kPA) Pressure: solo rider Tire pressure and wear Rear: 36-40 psi (248-276 kPA) Replace if less than 1/32 in. (0.8 mm) of tread pattern Wear 55 in-lbs (6.2 Nm) minimum Spoke nipple torque Wheel spokes 99953-99A (12 oz.) D.O.T. 4 hydraulic brake fluid part number Brake fluid level Front: 0.20 in. (5.0 mm) Fluid level (from top of master cylinder reservoir) Rear: 0.26 in. (6.5 mm) Front: 7-10 in-lbs (0.8-1.1 Nm) Master cylinder reservoir cover screw torque Rear: 12-15 in-lbs (1.4-1.7 Nm) 0.016 in. (0.4 mm) Minimum brake pad thickness Brake pads and discs 75-102 in-lbs (8.5.-11.5 Nm) Brake caliper pad pin torque Front: 0.18 in. (4.5 mm) Minimum brake disc thickness Rear: 0.25 in. (6.3 mm) 0.008 in. (0.2 mm) Maximum brake disc lateral runout (warpage) 10 lb. (4.5 kg) Upward force applied at midpoint of bottom belt strand Drive belt deflection 3/8-7/16 in. (9.5-11.1 mm) FLHTP 1/4-5/16 in. (6.4-7.9 mm) FLHP/FLHPE 40-60 in-lbs (4.5-6.8 Nm) Air cleaner cover bracket screw torque Air cleaner 36-60 in-lbs (4.1-6.8 Nm) Air cleaner cover screw torque LOCTITE MEDIUM STRENGTH THREADLOCKER 243 (BLUE) Air cleaner cover screw Threadlocker Part No. 99642-97 (6 ml) LUBIT-8 SUPER OIL, Part No. 94968-85TV (1/4 fl. oz.) Lubricant part number Clutch cable 35-45 in-lbs (4.0-5.1 Nm) Handlebar switch housing screw torque

Incoming search terms:

YAMAHA YZF-R1P YZF-R1PC ASSEMBLY MANUAL

0

Filed Under (Yamaha) by admin on 26-02-2011

download
PREPARATION To assemble the motorcycle correctly, supplies and working space are required. Supplies oils, greases, shop rags. Workshop The workshop where the motorcycle is assembled should be clean and large. The floor should be level. Self-protection Protect your eyes with suitable safety spectacles or safety goggles when using compressed air, when grinding or when doing any operation which may cause particles to fly off. Product hands and feet by wearing safety gloves or doing. SYMBOLS USED ON CRATE CARTON Contents of the transport package are fragile therefore it shall be handled with care. Indicates correct upright position of the transport package. Transport package shall be kept away from rain. Insertion of the lift arm from this side is prohibited. Lift arm inserting position. -1- UNPACKING 1. Remove the frame cover 1. NOTE: To remove the frame cover, cut the vinyl bands around the cover using a cutter or scissors. 2. Remove the bolts 2 (upper bracket). 3. Remove the bolt 3 (front tire). 4. Remove the packing frames 4 (upward and sideways). NOTE: Remove the bolts while holding frame. NOTE: Before starting the assembly, check for damaged or missing parts. The parts are contained in the cartan and the motorcycle for damage, scratches and other defects. -2- PARTS LOCATION 1 Carton box -3- 1 Carton box Screw, washer and special nuts (windscreen) Bolt (front master cylinder) Bolt (handle crown and handlebar) Nut (rear view mirror) Nut (front reflector) Front reflector Vinyl bag 1 Plugs (handle crown) Owner’s manual Rear view mirrors Windscreen – -5- 1. Handlebar 1 2 3 4 5 6 1 1 1 1 2 1 Reservoir tank (brake) Hexagon socket bolt Crown nut Hexagon socket bolt Cap Hexagon socket bolt * V * V V * d = 6 (0.24), r= 12 (0.47) d = 6 (0.24), r= 25 (0.98) d = 8 (0.31), r= 30 (1.18) 2. Front reflector A: Tighten the crown nut to specified torque. Tightening torque: 115 Nm (11.5 m • kg, 85.0 ft • lb) B: Tighten the bolt to specified torque. Tightening torque: 13 Nm (1.3 m • kg, 9.4 ft • lb) C: Tighten the bolt to specified torque. Tightening torque: 13 Nm (1.3 m • kg, 4.4 ft • lb) A: Tighten the screws to specified torque. Tightening torque: 40 Nm (4.0 m • kg, 29 ft • lb) 1 2 3 4 5 2 2 2 4 4 Reflector bracket Reflector Nut Washer Caliper bolt * V V * * d = 5 (0.20) d = 10 (0.39) d = 10 (0.39), r= 30 (1.18) 3. Clutch cable 1 Clutch cable 1 * A: Check the clutch lever for smooth action. CAUTION: Proper cable routing is essential to assure safe motorcycle operation. Refer to “CABLE ROUTING

Incoming search terms:

HARLEY DAVIDSON PIVOT BOLT COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 22-02-2011

download
This kit fits all 2004 and later XL (Sportster®) model motorcycles INSTALLATION Right-Side Pivot Bolt Cover Installation Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 1. See Figure 1. Start a set screw (2) from the kit into one of the pivot bolt covers (1) about two or three turns. 2. Note the position of the bottom-most flat on the rear-fork pivot hex-head bolt (3). Line up the pivot bolt cover over the bolt head so the set screw is centered on the hex flat. Use the 3/32 inch hex key from the kit to tighten the set screw securely to the head of the rear-fork pivot bolt. 3. Make sure the pivot bolt cover is clean and free of any oil or grease. Remove the protective backing from the adhesive disk on the back of the decorative insert (9). Install the decorative insert onto the end of the pivot bolt cover with the image or text upright and parallel to the ground. Press the insert firmly against the end of the pivot bolt cover and hold pressure for 30 seconds. After releasing pressure, avoid direct contact with the insert for about 20 minutes. Left-Side Pivot Bolt Cover Installation 4. Models without passenger footrests: Use an 8 mm hex key to remove the bolt (5) retaining the double-tube clamp (4). Models with passenger footrests: Use an 8 mm hex key to remove the two bolts (5) and the left-side passenger footrest and bracket assembly (6). 5. Start a set screw (2) from the kit into one of the pivot bolt covers (1) about two or three turns

Incoming search terms:

2006 KTM 250 SX-F 250 EXC RACING 400 EXC RACING 450 SX, XC, EXC RACING 525 SX, XC, EXC RACING, REPAIR MANUAL

0

Filed Under (KTM) by admin on 05-05-2012

download
Hot start lever (250 SX-F) If you pull the red hot start lever [1] during the starting procedure backward, a bore in the carburetor will be opened through which the engine may take in additional air. The result is a „lean” fuel-air mixture of the type needed for hot starts.
ENGLISH 7 OPERATION INSTRUMENTS » Headlamp switch (EXCUSA) In this model the headlamp is switched on with the pull switch [1] . Flasher switch The flasher switch is a separate unit and is mounted on the left portion of the handlebar. The wire harness is designed in a way that whenever you want to use your bike off-road, you can dismount the entire turn indicator system without affecting the function of the remaining electrical system. Flasher left Flasher right Starter button (EXC) Pushing the black starter button [2] will actuate the E-starter. Emergency OFF switch (EXC Australia) The red emergency-OFF switch [3] is arranged adjacent to the throttle grip. In this position, the E-starter is operational and the engine can be started. In this position, the E-starter and ignition circuits are interrupted.The E-starter cannot be actuated, and the engine will not start, not even if you attempt to start it with the kickstarter. Pushing the black starter button [4] will actuate the E-starter. 2 3 4 5 6 Indicator lamps The green control lamp [5] flashes in the same rhythm as the flashing indicator when the indicator is working. The blue control lamp [6] lights up when the high beam is on

Incoming search terms:

KTM 125 EXC, EXC SIXDAYS 200 XC, XC-W, EXC 250 XC, XC-W, EXC, EXCSIXDAYS 300 XC, XC-W, EXC-E, EXC-ESIXDAYS OWNER'S MANUAL 2008

0

Filed Under (KTM) by admin on 02-12-2010

download
Chassis number The chassis number is stamped on the right side of the steering head tube. Enter this number in the field on page no 1. Engine number, engine type The engine number and the engine type are stamped into the left side of the engine below the engine sprocket. Enter this number on page 1. Clutch lever The clutch lever [1] is located on the left side of the handlebars. The adjusting screw [A] is used to change the original position of the clutch lever (see maintenance work on chassis and engine). The clutch is hydraulically actuated and adjusts itself automatically. Hand brake lever The hand brake lever [2] is mounted on the handlebars on the right and actuates the front wheel brake. The adjusting screw [B] can be used to change the basic position of the hand brake lever (see maintenance work on chassis and engine). OPERATION INSTRUMENTS » 1 2 A B
ENGLISH 6 OPERATION INSTRUMENTS » TEST All of the display segments briefly light up for the display function test. WS (wheel size) The display changes and the circumference of the front wheel is briefly displayed in millimeters (2205 mm corresponds to a front wheel circumference of 21″ with production tires). Afterwards the display will return to the previous display mode. Electronic speedometer The display in the electronic speedometer is activated as soon as you press a button on the speedometer or an impulse is received from the wheel sensor. The display lights up when the engine is running. The display is cleared if no button is pressed for 1 minute or no impulse is received from the wheel sensor. The button is used to change between display modes. The + and – buttons are used to control various functions. SPEED display mode / H (service hours) Only the SPEED / H and SPEED / ODO display modes are activated in the condition at delivery. SPEED/H is displayed whenever the display is activated and the front wheel is not turning. It automatically changes to the SPEED/ODO display mode as soon as the front wheel starts turning. SPEED displays the speed. H displays the engine’s service hours. The service hour counter starts to count as soon as you start the engine. The displayed figure cannot be changed. Service intervals are indicated in service hours for some KTM offroad motorcycles, making the service hour counter a very practical function. SPEED / ODO display mode (odometer) The SPEED/ODO mode displays the speed and the total distance traveled. The display automatically changes to the SPEED/H display mode when the front wheel stops turning. + button no function – button no function briefly press buttonchanges to the next display mode hold button 3 secs. changes to the next display mode The electronic speedometer has a number of display modes (functions) that you can also activate (reveal) (see: Activating and deactivating display modes).
ENGLISH 7 OPERATION INSTRUMENTS » SPEED / LAP (lap time) display mode You can use the manual stop watch to stop and store up to 10 lap times, which you can view in the LAP/LAP display mode (see below). LAP displays the lap times in hours, minutes and seconds. + button Starts and stops the stop watch, lap time is not reset to 0 – button Stops the stop watch, stores the lap time and restarts the stop watch again. The time is reset to 0. A total of 10 lap times can be stored. If the lap time continues to run after you press the – button, all 10 memory locations are occupied.To clear all of the stored lap times, hold the button for 3 seconds in the SPEED/LAP mode.Up to 10 lap times can be stored in this way. briefly press buttonChanges to the next display mode.If no lap time is stored or the motorcycle is driving, the LAP/LAP mode will be skipped. hold button 3 secs. Clears all LAP figures SPEED / CLK (time) display mode CLK displays the time in hours, minutes and seconds. + button no function – button no function briefly press buttonchanges to the next display mode hold button 3 secs. set the clock menu To set the clock, see „Setting the clock”. Activating and deactivating display modes In the display mode SPEED/H, press and hold the button for 3 seconds to access the SETUP menu. The active functions will be displayed. The blinking function can be activated by pressing the + button and deactivated by pressing the – button. Press and hold the button 3 seconds to store the settings. If no button is pressed for 20 seconds, the setting will be stored automatically and the display will return to the SPEED/H mode. + button activates the blinking display – button deactivates the blinking display briefly press buttonchanges to the next display without changing any settings hold button 3 secs. starts the SETUP stores the settings and changes to the SPEED/H mode

Incoming search terms:

1981-1983 Yamaha Virago 750 & 920 Installation Instructions

0

Filed Under (Yamaha) by admin on 11-02-2012

download
Start by loosening the rear cylinder down tube bolt located on the top of the old mufflers center collector in front of the rear tire. 2. Remove both of the front cylinder exhaust pipe head nuts and set them to the side for reuse with the MAC exhaust system. 3. Remove the right side passenger’s foot peg. Set the foot peg aside as you will need to reinstall it. 4. Remove the left side passenger’s foot peg. Set this foot peg aside as it will also need to be reinstalled. Note: When you remove this bolt the entire exhaust system will be loose and may fall. You will need to support the old exhaust at this point to keep from injuring yourself. Gently move the old exhaust system side to side to remove it from the rear cylinder down tube. Once the exhaust system is loose from the down tube remove the system from under the Virago. 5. Remove the bolt holding the rear brake pedal in place and remove the brake pedal from the motorcycle. Note: Set both the bolt and the pedal aside for reinstallation. 6. Next loosen the nut on the drivers right foot peg, 1 full turn to start with. Then remove the rear nut on the same foot peg. (Note: The bolt that this nut is on goes completely through the motorcycle. This is the center stand mounting bolt.) Now remove the front nut and set both aside for reuse with the MAC system. 7. Install the center stand stop bracket under the left passenger foot peg. Install this bracket with the 90° bend facing down and towards the rear tire. (Note: Center stand sop bracket in provided in the hardware kit and is approx. 5″ long with a 90° bend in it.) Adjust the bracket by one of the large bolts through the foot peg then through the bracket and then install it into the stock location. Put on one of the washers and a nut and snug up the nut. Lower the center stand until the center stand come in to contact with the bottom of the bracket. Tighten the nut until it will hold the bracket securely. 8. Install the rear down tube clamp onto the rear muffler and install the medium sized nut/bolt/washer onto the clamp just finger tight. 9. Install the (2) small bolts into the channel bracket on the rear muffler. Install the rear mounting bracket onto the two bolts and then install the washers and nuts onto each. Tighten the (2) nuts only slight amount so that you can slide the bracket front to rear to insure that when you install the bracket you position it properly. 10. Slide the rear pipe onto the rear down tube about ¼”to ¾” past the pre-cut slots on the rear muffler pipe. Slightly snug the clamp making sure that the position of the bolt and nut will not interfere with any moving parts. The final position of this bolt can hit the tire if it is not positioned properly. 11. Install the other large bolt into the right passenger and then through the top hole in the rear muffler mounting bracket. Insert the bolt into the stock location and install the washer and the nut. 12. Align the rear muffler and you can then tighten the nuts on the rear muffler mounting bracket, the cylinder down tube and the right side passenger foot peg.
13. Install the front muffler on the rear most mounting bolt of the drivers foot peg and put the stock nut back onto the bolt. Hand tighten the bolt only at this time. Note: Install the nut at this time is only to support the muffler and to insure that the pipe does not fall on the ground while you complete the next step. 14. Lift the front head pipe into position and start the stock nuts onto the studs. It is strongly recommended that you install new exhaust gasket at this time. Note: The new exhaust gaskets are not included in the kit but are available at your local Yamaha Dealer. After gaskets are installed hand tighten the front head pipe. 15. Remove the nut from the drivers foot peg bolt and reinstall the drivers foot peg. Note: Hand tighten only at this time. 16. Finish tightening the nuts on the front head pipes. (Install these nuts according to Yamaha’s Factory specifications.) Once the nuts are tightened on the head pipe you can then tighten the drivers foot peg nuts. 17. Reinstall the rear brake pedal and tighten the bolt that holds it on to factory specifications. 18. Check all of the bolts that you have installed of removed to insure that they are tight. 19. Start the motorcycle and check for any leaks. 20. You are finished with your new MAC Exhaust System.

Incoming search terms:

2008 KTM 125 SX, 144 SX, 250 SX OWNER'S MANUAL

0

Filed Under (KTM) by admin on 25-11-2010

download
Short circuit button (SX) The short circuit button [1] turns off the engine. When pressing this button, the ignition circuit is short-circuited. Filler cap To open it: Press the release button [2] and turn the tank cap in a counterclockwise direction. To close it: Put the tank cap back on and turn in a clockwise direction until the release button snaps into place. Install tank breather hose [3] without kinks. Fuel tap OFF In this position the fuel tap is closed. No fuel can flow to the carburetor. ON During operation the twist grip must be turned to ON. This means that the fuel can flow to the carburetor. Choke knob When pulling the choke knob [4] fully towards the top, a bore is opened in the carburetor. Through this bore the engine can take in additional fuel. This results in a rich fuel-air mixture, that is needed for a cold start. When pressing the choke knob downward in the carburetor, the bore is closed again. ON OFF 4 1 2 3 ENGLISH 7 Shift lever The shift lever is mounted on the left side of the engine. The position of the gears is shown in the illustration. Neutral, or the idle speed, is located between first and second gear. OPERATION INSTRUMENTS » Kickstarter The kickstarter is mounted on the left side of the engine. Its upper part can be swivelled. Foot brake pedal The foot brake pedal is disposed in front of the right foot rest. Its basic position can be adjusted to your seat position (see maintenance work). 1 N 2,3,4,5, (6) 2 3 1 Compression damping of fork Hydraulic compression damping determines the reaction when the fork is compressed. The degree of compression can be adjusted with adjusting screws at the bottom of the fork legs. Turn the screw [1] clockwise to increase damping, turn it counterclockwise to reduce damping during compression. STANDARD ADJUSTMENT: -turn adjusting screw clockwise as far as it will go -turn it back by as many clicks as are specified for the relevant type of fork Typ WP Suspension 14187D01 . . . . .14 clicks Typ WP Suspension 14187D03 . . . . .14 clicks

Incoming search terms:

Incoming search terms: