1998 yamaha vstar 650 manual

You search Auto repair manual PDF 1998 yamaha vstar 650 manual, if there are search results will appear below. If search results do not exist, please search by others keyword.



  1998 yamaha vstar 650 manual Direct Download speed 5282 Kb/s

  1998 yamaha vstar 650 manual Full Version speed 6162 Kb/s



BMW F 650 CS Rear belt wheel cracks Removal And Installation Manual

0

Filed Under (BMW) by admin on 12-11-2010

download
Relieve the tension of the toothed belt and lift the belt off the belt wheel (refer to F 650CS Repair Manual, 00.57). 2) Remove 6 screws (see arrow in photo at right). 3) Remove the rear belt wheel. 4) Clean and degrease the tapered bores and the threads of the mounting screws 5) Carefully place the new belt wheel in position on the damper, coat the screw threads with Loctite 243 and hand tighten the securing screws. 6) Tighten the securing screws to the specified torque maintaining a diagonally opposite tightening sequence throughout (Torque to 28 NM, curing time 12 hours). 7) Measure the vertical runout of the belt wheel (refer to F 650 CS Repair Manual, 33.15). 8) Install and adjust the rear drive belt (refer to F 650 CS Repair Manual 00.57 – 00.58) 2.1 Removal of the front belt wheel Remove the front belt wheel in accordance with the instructions detailed in the F 650 CS Repair Manual. Remove the securing screw of the activated charcoal filter and let the filter canister hang by one side by the hoses, or remove it and lay it aside. Clean the splines and threads of the main shaft in order to remove all traces of Loctite. If necessary, remove corrosion from the main shaft spline (use only a brass bristle brush). 2.2 Visual inspection Check the splines of the main shaft for damage. Replace the main shaft if the splines are damaged (broken, chipped, bent or damaged teeth). Refer to the F 650 CS Repair Manual for this procedure.

Incoming search terms:

YAMAHA V-Star 650 BIG AIR KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 21-01-2012

download
Remove fuel tank and air filter assembly per Yamaha service manual procedures. 2. Remove the air silencer box under the tank. 3. Install supplied BA-2410-00 Needle/Jet kit according to the instructions in the jet kit package being sure to use the Jets and Needle Slot setting called out for the external BAK filter assemble. 4. Reinstall the air silencer box under the tank. 5. Remove the rubber boot from the stock air box. It is glued-in from the factory, but will come loose if gently persuaded. See photo #1 Our install guides provide a basic outline on the proper installation of our products. Further tuning and/or fitment may be required. Barons bears no responsibility on installation costs associated with this product. © 2010 Barons Custom Accessories 7401 Slater Ave. Huntington Beach, CA 92647 (714)274-4065 – Ph. (714)848-0718 – Faxwww.baronscustom.comtech@baronscustom.com Page: 2 BA-2011-00/03/06/07/13/13B BIG AIR KIT – YAMAHA V-Star 650 6. Install the stock rubber boot into your new Baron air filter backing plate with the supplied glue. Squeeze glue liberally into sealing groove in stock rubber boot. See photo #2 Allow glue to set up and dry prior to mounting onto bike

Incoming search terms:

Yamaha V-Star 650 Rear Lowering Kit REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 18-10-2010

download
INSTALLATION PROCEDURE 1. Secure motorcycle to a bike lift and raise the motorcycle. 2. Remove stock rear shock from the motorcycle per standard Yamaha shop manual instructions. 3. Place the shaft of the shock in V” blocks and secure this in a vice or press, applying firm pressure to the V” blocks to trap the shaft so it will not turn. Unscrew the upper shock mount eyelet from the shaft. NOTE: The upper mount is a standard thread so you will rotate the mount counter-clockwise to unscrew it. 4. Next, screw the New LA Choppers Shock Mount onto shock shaft using Loctite. 5. Re-install shock spring, making sure it is locked in place with the retaining ring prior to slowly releasing the spring compressor. Allow shock spring to expand against the retaining ring and machined washer. 6. Reinstall shock onto the motorcycle per standard Yamaha shop manual instructions. WARNING: Installing a lowering kit will decrease initial ground clearance. The motorcycle will be lower to the ground and care should be taken to avoid bottoming, especially over bumps or in turns. To maintain proper balanced geometry, the front and rear of the motorcycle should be lowered equally. Failure to properly install the lowering kit and operate the motorcycle after installation may result in serious injury or death to the rider. LIMITED GUARANTY: Because we cannot control the application of our products, buyer assumes risks for any and all damage caused to him or herself or any third party by virtue of any failure of these parts. Guaranty for such parts is limited to our replacement costs thereof. This guaranty is in lieu of all other guaranties or warranties express or implied, and all other such guaranties or warranties are hereby expressly disclaimed. By installation of these parts, buyer irrevocably agrees to the foregoing

Yamaha 1998 XVS1100 REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 03-01-2012

download
EXPLODED DIAGRAMS To help identify parts and clarify procedure steps, there are exploded diagrams at the start of each removal and disassembly section. 1. An easy-to-see exploded diagram 4 is provided for removal and disassembly jobs. 2. Numbers 5 are given in the order of the jobs in the exploded diagram. A number that is enclosed by a circle indicates a disassembly step. 3. An explanation of jobs and notes is presented in an easy-to-read way by the use of symbol marks 6 . The meanings of the symbol marks are given on the next page. 4. A job instruction chart 7 accompanies the exploded diagram, providing the order of jobs, names of parts, notes in jobs, etc. 5. For jobs requiring more information, the step-by-step format supplements 8 are given in addition to the exploded diagram and the job instruction chart.
24 21 18 15 16 17 10 12 13 11 14 1 3 5 7 9 2 4 8 6 19 20 22 23 25 EB003000 ILLUSTRATED SYMBOLS Illustrated symbols 1 to 9 are printed on the top right of each page and indicate the subject of each chapter. 1 General information 2 Specifications 3 Periodic inspections and adjustments 4 Engine 5 Cooling system 6 Carburetion 7 Chassis 8 Electrical 9 Troubleshooting Illustrated symbols 10 to 17 are used to identify the specifications appearing in the text. 10 Can be serviced with engine mounted 11 Filling fluid 12 Lubricant 13 Special tool 14 Torque 15 Wear limit, clearance 16 Engine speed 17 Ω, V, A Illustrated symbols 18 to 23 in the exploded diagrams indicate the types of lubricants and lubrication points. 18 Apply engine oil 19 Apply gear oil 20 Apply molybdenum disulfide oil 21 Apply wheel bearing grease 22 Apply lightweight lithium-soap base grease 23 Apply molybdenum disulfide grease Illustrated symbols 24 to 25 in the exploded diagrams indicate where to apply locking agent 24 and when to install new parts 25. 24 Apply locking agent (LOCTITE) 25 Replace

Incoming search terms:

Yamaha V-Star 650 Jet Kit REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 16-01-2012

download
Remove the vacuum slide from the carburetor. • Remove the OEM needle and spacer, noting the order of assembly. • Counting from the top to the bottom, install the new Baron needle clip on groove #4 of the replacement Baron adjustable needle. • Reinstall the OEM spacer and washer. • Reinstall the vacuum slide along with the diaphragm spring. • Reattach the diaphragm cover and tighten its screws. Note: Verify that the slide maintains a full range of movement! • Drain the fuel from float bowl and remove the bowl cover. • Remove the new cap head Allen screws in place of the OEM Phillips head screws. • Repeat above steps for other OEM main jet and pilot jet, and replace them with Baron’s main and pilot jets. • Thoroughly clean the inside of the float bowl prior to reinstalling it. • Reassemble the carburetor by reversing the order of previous steps. Use thecarburetor. • Locate the fuel mixture plug on each carburetor; it will either be a screw head or a brass plug. If it is a screw head, skip to step c . If you see a brass plug with a small hole in the center, proceed as follows: a. With a 5/32″ drill bit, carefully and slowly drill through the fuel mixture plug for each carburetor. CAUTION: The fuel mixture screw is located directly beneath this plug. Be prepared to stop the drill and remove the bit the instant you break through the plug. b. Insert a self-tapping sheet metal screw into the drilled hole and remove the plug. 311 #1 Industrial Way – Fallbrook, CA 92028 – USA Phone: (760) 731-1200 Fax: (760) 731-1284 E-mail: tech@baronscustom.com Website: www.baronscustom.com Included in this kit: (2) Mikuni main jets, (2) pilot jets, (2) titanium needles, (2) clips, (8) cap head Allen screws Revision 2.0 c. With air/fuel screw now accessible, use a flat blade screwdriver to turn the screw clockwise until it seats, then carefully turn it counter-clockwise 3 turns. Refer to final step for assistance in fine-tuning the setting of the air/fuel adjustment screw. • Reinstall the OEM air filter assembly. • Check all vent lines, fuel lines, and linkage for any obstructions or blockage

Incoming search terms:

Yamaha V-Star 650 Engine Guard REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 03-01-2012

download
Protect the rear portion of the front fender with a towel or other thick, soft cloth. Remove the OEM engine guards if they have been installed on the motorcycle. Your new Barons engine guard will fasten to the frame at the same points as the OEM guard and will use the same hardware. 2. Or, if OEM engine guards are not present, remove the 14mm bolts from the underside of the drivers footpeg mounts. 3. Remove the 12mm upper engine mount bolts located on both sides of the frame. Replacement bolts are included with your new engine guard. 4. Position the engine guard so that the lower brackets point towards the rear of the motorcycle, and slide the engine guard into the space between the front wheel and the frame. 5. Raise the guard until the holes in the lower mounting brackets align with the vacated bolt holes beneath the drivers footpegs. Due to production line tolerances in both the motorcycle and the engine guard, the mounting brackets may be too wide or too narrow for the frame. If this is the case, remove the guard from the motorcycle. Place the guard on a flat, firm surface. Insert a towel or other protective material between the guard and the surface. Using a rubber mallet or a block of wood and a hammer, tap the lower brackets until they are correctly spaced. 6. Insert the large washers (supplied with the guard) between the rear face of the lower bracket and the frame. The washer fills the space between the lower mounting bracket and the footpeg mount. Reinsert the 14mm bolts and finger tighten. 7. Rotate the guard until the holes in the upper mounting brackets align with the empty holes on each side of the frame. 8. Insert the replacement 13mm bolts, along with their washers, and tighten securely. Tighten all other nuts and bolts securely. 9. Remove the protection on the front fender and you’re ready to ride. CAUTION!!! You must re-tighten all four of the engine guard mounting bolts after 100 miles of riding! Care & Cleaning: Engine guards take the full brunt of the worst of what the weather in your area has to offer, making it critical that proper and complete cleaning take place on a weekly basis, or corrosion will occur which is not covered by warranty! Proper cleaning procedure would be to use a product like Simple Green, LOC, Salt-Away or similar. Mix a strong batch and apply it liberally with a soft towel or soft nylon brush to the entire

Incoming search terms:

Yamaha V-Star 650 REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 10-01-2012

download
Instruction sheet 54-600 1 Front head pipe 54-600-01F 1 Rear head pipe 54-600-01R 1 Front heat shield 54-600-02F 1 Rear heat shield 54-600-02R 1 Outlaw muffler 50-103-127 1 Muffler bracket 54-600-40 1 Head flange 54-110-41 7 2″ standard hose clamps 70-100-35 2 1 3/4″ HD Hose clamp 70-100-37 2 5/16″-18 carriage bolts 70-100-10 2 5/16″-18 flange nuts 70-100-15 1 8mm x 1.25 x 25mm flange bolt for front head flange 70-100-09 2 8mm x 1.25 x 20mm bolts /muffler bracket 70-100-05 2 10mm x 1.25 x 35mm bolts 70-100-85 2 Spacer .250 x .438 x .875 50-100-74 2 8mm x 1.25 Flange nut 70-100-22
Disassembly 1. Remove both Allen bolts that hold the muffler together (Fig. 1) . Also Loosen clamp from the front muffler to front head pipe (Fig. 2) , and remove allen bolts from rear head pipe and remove in one peace carefully (Fig. 3) . Figure 1 Figure 2 Figure 3 2. Once the two mufflers are removed with the rear head pipe, remove bracket by removing two 8mm bolts as shown and remove bracket. (Fig 4) Figure 4
3. Remove spring from brake light switch to the brake rod located on the right side footrest. (Fig 5) Figure 5 4. Remove two bolts holding the footrest, and brake pedal (Fig. 6) . Carefully rest right side footrest on the floor or you can use a two by four to rest the footrest onto. Figure 6

Incoming search terms:

YAMAHA V-STAR 650 CA SHORTSHOTS STAGGERED INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 29-12-2011

download
Check condition of stock exhaust gasket. Replace if damaged or worn. 2. Install mounting bracket (stamped 384-P) in the original bracket mounting position using two 8mm bolts (supplied)(Figure 1). Note: Install two 5/16″ x 5/8″ fl ange bolts (supplied)(Figure 1) into top holes of bracket before installing bracket onto motorcycle. 3. Mark outside surface of front and rear heat shields with location of mounting clips that are welded to the inside (Figure 2). Place each heat shield on a non abrasive surface such as a blanket or carpet. Lay each head pipe/muffl er onto its respective heat shield (Figure 3). 4. Loosely install each hose clamp by feeding tail end of clamp into heat shield clip (Figure 2). #20 hose clamps are for head pipes and #28 hose clamps for muffl er area. Take note of clamp screw head direction (Figure 4). Screw head should be accessible when system is installed on motorcycle for adjustment purposes. Note: Do not tighten yet. 5. Install 6″ fl ange bolts (supplied) engaging nut plate. Leave T-bolt clamp onto front muffl er (Figure 4&5). Slide muffl er onto front head pipe. Slide nut plate (supplied) inside bracket welded to backside of front muffl er (Figure 6). Attach muffl er to mounting bracket 384-P using two 5/1head pipe/muffl er assembly loose at this time. 6. Using stock Allen bolts, carefully install rear head pipe/ muffl er assembly into exhaust port. (Assistance may be required). Note: Do not tighten yet. 7. Slide nut plate (supplied) inside bracket welded to backside of rear muffl er (Figure 6). 8. Align muffl ers so they are parallel when viewed from the right side of the motorcycle and muffl er tips align at the same length. Tighten 5/16″ fl ange bolts securing muffl ers to bracket. 9. Tighten cylinder exhaust port bolts securing head pipes to cylinder head. 10. Tighten T-bolt clamp securing front muffl er to head pipe. 11. Adjust heat shields so that muffl er tips protrude 1/4″ from heat shields (Figure 7) and rotation of heat shield matches muffl er tip. Tighten all hose clamps securing heat shields. 12. After installation and before starting motorcycle, completely clean pipes and muffl ers with cleaning solvent and a clean, soft cloth that will not leave a residue. Note: Any residue, oil, or fi ngerprints will stain the chrome when the metal heats up. 13. All hardware must be properly tightened before starting motorcycle

650 Yamaha V-Star InstaTrike REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 29-12-2011

download
install all bolts loosely until all brackets are in place y Remove any aftermarket accessories (saddle bags, back rests, etc) before hitch installation. After installation remount accessories. NOTE: Some aftermarket accessories may not be compatible with InstaTrike. 1) Place motorcycle on a firm level surface. 2) Remove rear foot pegs and bolts 3) Attach bracket A (left) and bracket B (right) to the inside of the rear foot peg bracket and reattach rear foot pegs using new bolts provided. 4) Attach front of bracket C (left) and bracket D (right) to bottom of brackets A and B 5) Attach bracket E (left) and bracket F (right) to two rear fender attachment bolts using new bolts provided 6) Attach brackets G and H to rear of brackets E and F 7) Attach bottom of brackets G and H to hitch plate. 8) Attach rear of brackets C and D to TOP of forward hitch arms. 9) Tighten all bolts. Installation Diagram Leveling stand screw jack installation 1) Thread right side screw jack into threaded hole on bracket D 2) Push motorcycle over from left side until right screw jack is touching floor. 3) Install left side screw jack on bracket C and adjust out until motorcycle will rest upright on both screw jacks. 4) Adjust screw jacks until motorcycle is level. CAUTION – Use screw jacks to hold motorcycle upright and level ONLY. Do not lift motorcycle with screw jacks. CAUTION – Use care when installing screw jacks. Be certain that motorcycle is always in a stable balanced position

YAMAHA V-Star 1100 Motorcycle Enhancements Remote Oil Filter Installation Manual

0

Filed Under (Yamaha) by admin on 10-11-2010

download
Removing Your Old Filter and Beauty Cover In order to install the new Remote Oil Filter Kit, you’ll need to remove the stock Yamaha “beauty cover” and the old filter and filter cover. Remove the engine parts necessary to access the stock filter as outlined in the V-Star owner’s manual. The parts should come off in this order: 1. Muffler assembly 2. Front exhaust pipe 3. Rear brake reservoir cover bolt and brake cover (the reservoir should not be removed, it can remain in place and be moved aside as needed) 4. Right floorboard (this can be simply loosened, by loosening the two bolts underneath) With the above parts removed, you can remove the Allen bolts holding the beauty cover and filter cap from your engine. There are five Allen bolts holding the beauty cover (so named, because most of the cover just covers the chromed side of the engine There are five bolts holding the cover. Ignore the three on the “Yamaha” cap in the middle – these just hold the Yamaha cap to the beauty cover itself. One bolt is hidd – in this picture – just be the Yamaha ca en low p. The bottommost bolt on the beauty cover will likely leak some oil when you remove it – it holds on the inner oil filter cover. Once you remove the beauty cover, you can remove the oil filter cover, and the oil filter Keep these two “O” rings, you’ll need them for the remote kit Old oil filter. Toss it away; you’ll never need one again! Throw away the old filter, and carefully remove the orange and black “O” rings from the filter cover (see picture above). These two “O” rings will go on the new engine cap in the same order as on the old filter cover. “O” ring for bottom bolt. When the beauty cover and filter cover are removed, be sure not to lose the tiny “O” ring that the bottom bolt goes through. Preparing the Remote Oil Filter Kit Remove the orange and black “O” rings from the stock filter cover plate, and place them on the Remote Oil Filter Kit engine cap – black on the inside, orange on the outside – just like on the stock filter cover.

Incoming search terms:

Incoming search terms: