1990 ke100 wiring harness

You search Auto repair manual PDF 1990 ke100 wiring harness, if there are search results will appear below. If search results do not exist, please search by others keyword.



  1990 ke100 wiring harness Direct Download speed 5282 Kb/s

  1990 ke100 wiring harness Full Version speed 6162 Kb/s



2002-2005 Honda VFR800/A Wire Harness Replacement Manual

0

Filed Under (Honda) by admin on 21-04-2011

download
If the 18P (light blue) connector is in abnormal condition as shown below, contact TechLine at (800) 421-1900, option 9. FRONT SUB-HARNESS REPLACEMENT 1. Remove the front sub-harness from the cowl stay hooks. Disconnect all the electrical components from the front sub-harness. 2. Temporarily set the main wire harness aside, and disconnect the 6P (natural) con- nector. Then, carefully remove the front sub-harness. 3. Install the new front sub-harness by con- necting the 14P (natural) and 18P (light blue) connectors. NOTE: For routing specifications, refer to the WIRING & HARNESS ROUTING SECTION on pages 7-8. 4. Attach the front sub-harness on the cowl stay hooks. Make sure the front sub-harness is routed elow the main sub-harness. ABNORMAL CONDITION STAY HOOKS 6P (NATURAL) CONNECTOR FRONT UB-HARNESS 14P (NATURAL) CONNECTOR 18P (LIGHT BLUE) CONNECTOR FRONT SUB-HARNESSSTAY HOOK Page 4 VFR800/A #4 4 of 12 NOVEMBER 2007 5. Place the front sub-harness between the radiator and the frame, and below the rec- tifier. Be careful not to damage the front sub-harness or other components. 6. Re-connect the front sub-harness to the 6P (natural) connector. 7. Secure the main wire harness and the front sub-harness using the longer wire band. 8. Secure the main wire harness and the upper side of the front sub-harness using the shorter wire band. Adjust the wire har- ness located within the frame and the radi- ator hose accordingly. 9. Secure the main wire harness fuse box to the front sub-harness using the shorter wire band. FRONT SUB-HARNESS STAY HOOK MAIN-HARNESS FRONT SUB-HARNESS FRONT SUB-HARNESS 6P CONNECTOR (Male) 6P CONNECTOR (Female) WIRE BAND (LONG) WIRE BAND (SHORT)
WIRE BAND (LONG) WIRE BAND (SHORT) MAIN WIRE HARNESS FUSE BO

Incoming search terms:

TOYOTA COROLLA 1984-2006 VEHICLE WIRING VEHICLE WIRING REMOVAL

0

Filed Under (Toyota Manuals) by admin on 04-10-2011

download
IRING INFORMATION: 1984 Toyota Corolla FWD WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE WHITE OR WHITE/RED Ignition Harness STARTER WIRE BLACK/WHITE Ignition Harness IGNITION WIRE BLACK/YELLOW Ignition Harness SECOND IGNITION WIRE BLACK/ORANGE Ignition Harness ACCESSORY WIRE BLUE/RED Ignition Harness POWER DOOR LOCK (-) BLUE/WHITE Harness In Driver’s Kick Panel POWER DOOR UNLOCK (-) BLUE/RED Harness In Driver’s Kick Panel PARKING LIGHTS (+) DK. GREEN Harness In Driver’s Kick Panel PARKING LIGHTS (-) LT. GREEN Harness At Steering Column HEADLIGHTS (-) RED/WHITE Harness At Steering Column DOOR TRIGGER (-) RED/WHT OR BLK/WHT Harness At Fuse Box TRUNK TRIGGER COMMON WITH DOORS (Hatchback Only) TACHOMETER WIRE BLACK At Ignition Coil BRAKE WIRE (+) GREEN/WHITE Brake Pedal Switch HORN TRIGGER (-) GREEN/RED Steering Column LEFT FRONT WINDOW UP GREEN/BLACK At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN BLUE/RED At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP GREEN Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN BLUE/WHITE Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW UP RED/BLACK Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW DOWN RED/YELLOW Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW UP RED/BLUE Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW DOWN BLUE/BLACK Harness In Driver’s Kick From Driver Doo

Incoming search terms:

HARLEY DAVIDSON ENGINE GUARD-MOUNTED FOG LAMP KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-02-2011

download
VRSC models: See Figure 3. Place the wire harness from the kit into the area in front of the battery. Do not block the air intake opening. All models except VRSC and 2004 and later XL models: See Figure 4. Install the wire harness from the kit. Place the relay in the opening of the frame under the seat area, and route the long leg of the harness forward along the frame backbone. 2004 and later XL models: See Figure 5. Remove the nuts retaining the ignition module (1) and temporarily reposition the module as shown. Place the relay in the recessed area (2) of the oil reservoir. Install the ignition module. Route the long leg of the harness along the frame backbone. CAUTION 1 WARNING -J02798 Figure 3. Install Fog Lamp Wiring Harness (VRSC Models) Place harness into this area but do not block air intake Air intake i04372 Battery Figure 4. Install Fog Lamp Wiring Harness (All Models Except VRSC. Dyna Model Shown) i02286.eps 1. Relay 2. Ground stud 3. Long leg of harness 2 1 3 2 of 6 Figure 2. Fog Lamp Wiring Harness Figure 1. Fog Lamp Schematic Ground To low beam To main circuit breaker Fuse N.O. Contact Switch Coil Fog lamp Fog lamp i01360a Relay 1. Fuse block 2. Relay 3. Connector to power 4. Ring terminals (Ground) 5. To fog lamps 6. Unterminated wire to low beam 7. Switch with boot and bracket 4 2 5 6 7 1 3 i05708 5. All 2003 and earlier models and VRSC: Cut the connector from the white power lead, and replace it with the ring terminal supplied in the kit. 6. All 2003 and earlier models, except VRSC: Connect the white wire with the ring terminal to the copper stud (BAT) terminal of the main circuit breaker. All 2004 and later models, except VRSC: Connect the white wire with connector to the B+ connector on the harness. All VRSC: Connect the white power lead to the battery positive terminal. 7. See Service Part illustration. Connect the black ground wires with the two ring terminals to the ground stud under the seat, or at any good electrical ground point. Secure the kit harness to the adjacent harnesses with cable straps (item 6) from the kit. When routing wires through the front fork, make sure the wires are clear of moving parts, to avoid pinching and possible short circuits. 8. Route the forward end of the harness past the steering head, and route the lamp switch leg of the harness along the left side of the handlebar to the clutch control. 9. See the Service Parts illustration. Obtain the switch mounting bracket (item 11) from the kit. Unscrew the boot from the lamp switch, and install the switch into the bracket. Replace the boot on the switch. NOTE If the boot becomes worn or damaged, or is lost, replace the boot to prevent moisture from entering the switch. See the Service Parts illustration (Item 12). 10. See Figure 6. Remove the lower screw (1) and washer from the clutch control clamp (3), and install the lamp switch and bracket assembly (2). Install the screw and washer and tighten to 60-80 in-lbs (7-9 Nm). 11. See the Service Parts illustration. Secure the lamp switch leg of the harness to the handlebar using the wire harness retainers already on the bike. Snap the retainers into the holes in the handlebar. 12. Remove the headlamp assembly. See HEADLAMP – REMOVAL instructions for the correct model in the Service Manual. CAUTION 3 of 6 -J02798 Figure 6. Install the Lamp Switch on the Clutch Control Clamp i04370 3 1 1. Lower clamp screw 2. Lamp switch and bracket assembly 3. Clutch control clamp 2 Figure 5. Install the Wiring Harness (2004 and Later Models) i05712 3

HARLEY DAVIDSON BATTERY CHARGING HARNESS (THREE-PIN) INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
1. Follow the instructions in your Owner’s Manual to remove the seat and any other components (side covers, etc.) necessary to provide access to the battery. 2. Refer to the applicable view in Figure 1 for your model. Break the battery negative (-) connection by removing the hardware assembly from the negative battery terminal. 3. Break the positive (+) battery connection by removing the hardware assembly from the positive battery terminal. 4. Clean the battery terminals and cable connectors using a wire brush or sandpaper to remove any oxidation. 5. Apply a light coating of Harley-Davidson electrical contact lubricant (Part Number 99861-02) to the battery terminals, cable connectors, battery charging harness ring terminals and connector located under the weather- shield cap. Connect positive (+) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00068a) 6. Refer to the view in Figure 1 used for disassembly. Install the positive (RED) lead of the harness to the positive (+) battery post following the sequence shown. • On 1999 and earlier models (with original equipment), torque the positive (+) terminal post bolt to 40 in-lbs (4.5 Nm). • On 2000 and later models (with original equipment), torque the positive (+) terminal post bolt to 60-96 in-lbs (6.8-10.9 Nm). 7. Attach the negative (BLACK) lead of the harness to the negative (-) battery post following the sequence shown. • On 1999 and earlier models (with original equipment), torque the negative (-) terminal post bolt to 40 in-lbs (4.5 Nm). • On 2000 and later models (with original equipment), torque the negative (-) terminal post bolt to 60-96 in-lbs (6.8-10.9 Nm). Harness Routing Do not route the harness near any moving parts. Contact with moving parts may result in damage to harness. Refer to the following sections to determine the correct harness routing for your model. Be sure to avoid any components that may pinch or cut the harness, and avoid components that radiate heat. Take up any slack in the cable and store out of sight. Secure the harness with cable straps (H-D Part Number 10006), which can be purchased separately from any Harley Davidson Dealer. VRSC Model Harness Routing 1. See Figure 2. Route the battery harness/ connector (3) toward the front of the bike following the upper left frame tube. Cleanly tuck the in-line fuse (2) into the space in front of the battery. 2. Continue to route the harness/ gray connector to the front of the bike and behind the vent cover. Secure the harness with a cable strap and let the connector protrude past the cover for easy access. Trim any excess from the cable strap

Incoming search terms:

HONDA GL-1500 Trailer Wire Harness with Relay INSTALLATION MANUAL

0

Filed Under (Honda) by admin on 27-02-2011

download
Seat: (if optional accessory wire is to be used) After removing trunk pan, run a stiff piece of wire from the bottom of the left saddlebag frame behind the rear tire up until it comes out under the trunk. Then hook open end of wire harness to fish wire and tape with electrical tape. Pull the harness back down to the bottom of the saddlebag frame. Route the long part of harness wire around the back of the license plate light to the right side 6-pin vertical connector just in front of tail light assembly. Unplug the stock connector and plug wire harness in between the stock plugs. Do the same for the left side with the short side of the Y on the harness. Now pull the slack down from the bottom of the harness and tuck all of the wires under the frames tubes so that the pan can be reinstalled without any problems. You can now hook up the loose ends of the harness to any style connector to match your trailer connector using the following color codes: GREEN GROUND ORANGE- LEFT TURN YELLOW- BRAKE BLUE- RIGHT TURN BROWN- TAIL RED POWER . Note : This accessory is an electronic isolated trailer wire harness. It should be installed by a qualified mechanic . 1. Disconnect the negative from the battery. 2. Install the harness. 3. When connecting to the trailer make sure all wires are used for the proper use and are waterproof. Make sure there are not exposed wires. Consult the trailer manufacturer for proper wiring. 4. Reconnect the battery negative. Double check the functions

SUZUKI SV 1000 RADIATOR (COOLING SYSTEM) SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
FI SYSTEM MALFUNCTION CODE AND DEFECTIVE CONDITION MALFUNCTION CODE DETECTED ITEM DETECTED FAILURE CONDITION CHECK FOR COO NO FAULT C11 Camshaft position sen- sor The signal does not reach ECM for more than 3 sec . after receiving the starter signal . The camshaft position sensor wiring and mechanical parts (Camshaft position sensor, intake cam pin, wiring/coupler con- nection) C12 Crankshaft position sensor The signal does not reach ECM for more than 2 sec . after receiving the starter signal . The crankshaft position sensor wiring and mechanical parts (Crankshaft position sensor, wiring/coupler connection) C13 Intake air pressure sensor The sensor should produce following voltage . (0.50 V < sensor voltage < 4 .85 V) Without the above range, C13 is indicated. Intake air pressure sensor, wiring/coupler connection C14 Throttle position sen- sor The sensor should produce following voltage . (0.20 V < sensor voltage < 4 .80 V) Without the above range, C14 is indicated. Throttle position sensor, wiring/coupler connection C15 Engine coolant temperature sensor The sensor voltage should be the following. (0.15 V <_ sensor voltage < 4 .5 V) Without the above range, C15 is indicated. Engine coolant temperature sensor, wiring/coupler connection C21 Intake air temperature sensor The sensor voltage should be the following. (0.15 V < sensor voltage < 4 .5 V) Without the above range, C21 is indicated. Intake air temperature sensor, wiring/coupler connection C22 Atmospheric pressure sensor The sensor voltage should be the following. (0.50 V < sensor voltage < 4 .5 V) Without the above range, C22 is indicated. Atm. pressure sensor, wiring/coupler connection C23 Tip over sensor The sensor voltage should be the following for more than 2 sec . after ignition switch turns ON . (0 .20 V < sensor voltage < 4 .80 V) Without the above value, C23 is indicated. Tip over sensor, wiring/coupler connection C24 or C25 Ignition signalCrankshaft position sensor signal is produced and ECM determines the ignition signal but signal from ignition coil is interrupted continuous by 4 times or more. In this case, the code C24 or C25 is indicated. Ignition coil, wiring/coupler connection, power supply from the battery SERVICING INFORMATION 8 .3 C28 Secondary throttle valve actuator No operating voltage is supplied from the ECM, C28 is indicated. STVA can not operate. STVA lead wire/coupler, STVA C29 Secondary throttle valve position sensor The sensor should produce following voltage . (0.10 V < sensor voltage < 4 .90 V) Without the above range, C29 is indicated . Secondary throttle position sensor, wiring/coupler connection C31 Gear position signalGear position signal voltage should be higher than the following for more than 2 seconds. (Gear position switch voltage >_ 0 .6 V) Without the above value, C31 is indicated. Gear position sensor, wiring/coupler connection, gearshift cam, etc. C32 or C33 Fuel injector Crankshaft position sensor signal is produced and ECM determines the injection signal but fuel injection signal is interrupted continuous by 4 times or more. In this case, the code C32 or C33 is indicated. Injector, wiring/coupler connection, power supply to the injector C41 Fuel pump relay No voltage is applied to fuel pump although fuel pump relay is turned ON, or voltage is applied to fuel pump although fuel pump relay is turned OFF . Fuel pump relay, connecting lead, power source to fuel pump relay C42 Ignition switchIgnition switch signal is not input in the ECM . Ignition switch, lead wire/coupler C44 Heated oxygen sensor (HO2S) [For E-02, 19] During 02 feedback control, 02 sensor voltage is higher or lower than the specification . No signal is detected during engine operation or no electrical power is supplied from the battery . HO2S lead wire/coupler connection Battery voltage supply to the HO2S C49 PAIR control solenoid valve (PAIR valve) When no operating voltage is supplied from the ECM, C49 is indicated. PAIR valve can not operate. PAIR valve lead wire/coupler

Incoming search terms:

2000-2010 KTM X2 SWITCH WIRING HARNESS Removal and Installation Manual

0

Filed Under (KTM) by admin on 25-01-2012

download
The included 3600-SWHA switch harness is intended for use with offroad models that do not come with a Hi/Low beam switch from the factory. The harness is compatable with stock AC lighting electrical systems as well as high output DC electrical systems. 1. Remove the stock numberplate or headlight. Remove the stock kill switch from handlebars and replace with the 3600-SWHA switch. 2. Remove the gas tank. Route the white and black leads from the 3600-SWHA under the tank following the wires from the stock kill switch. Disconnect the stock kill switch bullet and connect the white wire of the 3600-SWHA to the wiring harness. Disconnect the stock kill switch ring terminal and connect the ring terminal of the 3600-SWHA. Fully remove the stock kill switch. Be sure all the wires are safe from being burned or pinched and re-install the gas tank. 3. Disconnect the two female spade terminals from the stock headlight switch (if present). Connect the terminal with the yellow wire to the red power lead from the switch. Connect the white wire to the blue accessory output from the switch. Be sure the clear silicone sleeves are covering the stock plastic housings. 4. Connect the X2 headlight to the switch headlight plug. Note: The stock headlight plug will not be used for the X2 installation, but is still functional for connecting the stock headlight. The stock plug will turn on and off with the new headlight switch, and will be powered in either of the Low or High Beam positions

Incoming search terms:

HARLEY DAVIDSON DETACHABLE TOUR-PAK LIGHT HARNESS KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 08-03-2011

download
INSTALLATION Models with main FUSE: To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the Service Manual and follow the instructions given to remove the main fuse. Models with main CIRCUIT BREAKER: To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the negative (black) battery cable from the negative (-) battery terminal. Retain all seat mounting hardware. 2. ALL models: Install the Detachable Tour-Pak Rack Kit per the instructions in that kit, up to the point where the saddlebags are to be re-installed. NOTE Make note of the cable strap locations before releasing the harness from the upper frame tube. New straps will be fastened in the same location. 3. Cut the larger cable strap fastening Tour-Pak circuit [12] (see the Service Manual Wiring Diagram) of the vehicle main harness to the left-side upper frame tube, rearward of the shock absorber. Cut the small cable strap at the end of the circuit [12] conduit. 4. Slit the conduit open along its length to expose the final ten inches (0.25 M) of main harness circuit [12] wiring. Cut the three wires (Black, Blue, and Red with Yellow tracer) nine inches (0.23 M) from the three-way Multilock socket housing [12B]. The socket housing and cut wires can be discarded. 5. Obtain the socket housing, secondary lock (locking wedge), and three socket terminals from the kit. See the illustration at DEUTSCH ELECTRICAL CONNECTORS: REMOVING/INSTALLING SOCKETS in the Service Manual. Refer to CRIMPING INSTRUCTIONS in the Service Manual, and follow the instructions to install the terminals to the three wire leads of main harness circuit [12]. 6. Per the instructions under DEUTSCH ELECTRICAL CONNECTORS, insert the Blue lead and terminal into Cavity 1 of the new socket housing. Insert the Red/Yellow lead and terminal into Cavity 2. Insert the Black lead and terminal into Cavity 3. 7. Cut the excess conduit from main harness circuit [12]. 8. Obtain the two cable straps from the kit. As noted in Step 3, use one strap to bind the end of the main harness circuit [12] conduit. Use the second strap

HARLEY DAVIDSON SECURITY SYSTEM SMART SIREN AND SMART SIREN II KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 08-03-2011

download
INSTALLATION 1. Refer to the owner’s manual and follow the instructions given to disarm the security system and remove the left- side cover. Models with main FUSE: To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 2. Refer to the owner’s manual and follow the instructions given to remove the main fuse. ALL models: To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 3. Refer to the owner’s manual and follow the instructions given to remove the seat and disconnect the battery cables, negative (-) cable first. Retain all seat mounting hardware. NOTE For 2004 and later XL (Sportster®) models, the negative battery cable is most easily disconnected at the engine crankcase . 4. Remove the battery from the vehicle. 2 1 3 4 is 01377 1. Three-pin connector on siren harness 2. Three-pin connector [142B] on vehicle harness 3. Siren harness 4. Frame rear crossmember (not visible) Figure 1. Connect the Siren Harness to the Vehicle Harness 5. See Figure 1. Locate the siren connector (2) on the main harness, behind the harness shield forward of the battery location. It is covered by a dust cap. Pull the dust cap from the connector, and feed the connector downward and out from behind the shield. 6. Select the correct siren harness (3) for this model year vehicle from the kit. Route the three-pin connector (1) of the siren harness from the bottom of the motorcycle, between the primary cover and frame tube. Plug the connector into the siren harness connector (2) on the vehicle main harness. 7. Secure the connectors to the diagnostic harness using a cable strap from the kit. Route the long lead of the siren harness over the frame rear crossmember

ULTIMA ELECTRONIC WIRING SYSTEM INSTALLATION INSTRUCTIONS

0

Filed Under (Tips and Review) by admin on 03-03-2011

download
1. Find a mounting location for control box. The box is designed to be mounted to the top frame rail between split tanks, but can be mounted in a wide variety of places. If possible the box should be fastened using small screws or rivets but can be wire tied in place. Make sure the location is away from moving parts and heat sources. 2. Pre-fit harness to bike. Attach rear harness to control box. Each wire is color coded and labeled. Route individual wires to their destinations and do not cut to length. Keep wires in a bunch until they need to branch off. Use electrical tape to hold main wire bunch wherever individual or multiple wires branch off. Keep wires away from sharp edges or pinch points and leave extra wire for suspension movement. Repeat this for front and right/left harnesses. All wires not being used should be cut off at connector or secured to prevent shorts. When all wires are routed, cut excess length from ends leaving a couple extra inches for final fitment. 3 Remove pre-fitted harness from bike to install heat shrink tubing. Start at main connector and cut tubing approximately 1 inch past first branch. This will allow the next piece of tubing to slide into the first. Repeat this along entire harness. After encasing harness with heat shrink, use a heat gun to shrink tubing starting at main connectors. Be careful to not burn through the tubing with too much heat. Refit the harness to the bike, attaching to frame where necessary. Cut the ends of harness to length and strip the ends. Attach the terminals to the wire ends and use heat gun to shrink ends. Attach terminals to their destinations. 4. The diagnostic LED’s are used to locate shorts or overloads. Pinched or bare wires, faulty components or too much current draw usually causes these. If an LED is on, turn off the bike, locate and correct the problem, then turn the bike back on. The bike must be turned off to reset the protection circuit. If no LED’s are lit, but turn signals and dash lights do not work properly, make sure the control box main ground has a good connection to the chassis ground. 5. The control box operates the turn signals as listed: First command – flash 10 times then cancel Second command on same side – cancel Second command opposite side – cancel current sequence, flash 10 times then cancel Both sides at same time – hazard, all signals flash Brake switch – flash rear signals three times then stay on for 30 seconds

Incoming search terms:

Incoming search terms: